stm32測頻程序（輸入捕獲1khz-6mhz）

ID:200496 · 發表于 2017-6-25 19:40

stm32測頻（輸入捕獲）程序
頻率計 1khz-6mhz

單片機源程序如下:

#include "counter.h"
#include "stdio.h"
#include "usart.h"
/***********************************************************************************************
//上升沿捕獲
************************************************************************************************/
TIM_ICInitTypeDef TIM3_ICInitStructure;
void TIM3_counter_Init(u16 arr,u16 psc)
{
GPIO_InitTypeDef GPIO_InitStructure;
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
NVIC_InitTypeDef NVIC_InitStructure;
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); //使能TIM5時鐘
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); //使能GPIOA時鐘
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7; //PA7 清除之前設置
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING; //PA7 浮空輸入
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_ResetBits(GPIOA,GPIO_Pin_7); //PA7 下拉
//初始化定時器5 TIM5
TIM_TimeBaseStructure.TIM_Period = arr; //設定計數器自動重裝值
TIM_TimeBaseStructure.TIM_Prescaler =psc; //預分頻器
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1; //設置時鐘分割:TDTS = Tck_tim
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //TIM向上計數模式
TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure); //根據TIM_TimeBaseInitStruct中指定的參數初始化TIMx的時間基數單位
//初始化TIM5輸入捕獲參數
TIM3_ICInitStructure.TIM_Channel = TIM_Channel_2; // 選擇輸入端 IC1映射到TI1上
TIM3_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising; //上升沿捕獲
TIM3_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI; //映射到TI1上
TIM3_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1; //配置輸入分頻,不分頻
TIM3_ICInitStructure.TIM_ICFilter = 0x00; //IC1F=0000 配置輸入濾波器不濾波
TIM_ICInit(TIM3, &TIM3_ICInitStructure);
TIM_SelectInputTrigger(TIM3, TIM_TS_TI2FP2); //選擇IC2為始終觸發源
TIM_SelectSlaveMode(TIM3, TIM_SlaveMode_Reset);//TIM從模式：觸發信號的上升沿重新初始化計數器和觸發寄存器的更新事件
TIM_SelectMasterSlaveMode(TIM3, TIM_MasterSlaveMode_Enable); //啟動定時器的被動觸發
//中斷分組初始化
NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn; //TIM3中斷
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; //先占優先級2級
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; //從優先級0級
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能
NVIC_Init(&NVIC_InitStructure); //根據NVIC_InitStruct中指定的參數初始化外設NVIC寄存器
TIM_ITConfig(TIM3,TIM_IT_CC2,ENABLE);//不能允許更新中斷 ,允許CC2IE捕獲中斷
TIM_Cmd(TIM3,ENABLE); //使能定時器3
}
/***********************************************************************************************
************************************************************************************************/
u32 counter=0; // 每秒計數
u32 Frequency=0;
void TIM3_IRQHandler(void)
{
if (TIM_GetITStatus(TIM3, TIM_IT_CC2) == SET)
{
……………………
…………限于本文篇幅余下代碼請從51黑下載附件…………