STM32的OLED驅動

ID:124161 · 發表于 2016-6-3 21:46

STM32的OLED驅動， SPI通訊協議。

源代碼：

#include "oled.h"
#include "oledfont.h"
//向SSD1306寫入一個字節。
//dat:要寫入的數據/命令
//cmd:數據/命令標志 0,表示命令;1,表示數據;
void OLED_WriteCmd(unsigned char cmd)
{
unsigned char i;
DC(0);
CS(0);
for(i=0;i<8;i++)
{
SCL(0);
if(cmd&0x80)
{
DIN(1);
}
else
DIN(0);
SCL(1);
cmd<<=1;
}
CS(1);
DC(1);
}
void OLED_Writebyte(unsigned char dat)
{
unsigned char i;
DC(1);
CS(0);
for(i=0;i<8;i++)
{
SCL(0);
if(dat&0x80)
{
DIN(1);
}
else
DIN(0);
SCL(1);
dat<<=1;
}
CS(1);
DC(1);
}
void OLED_Set_Pos(unsigned char x, unsigned char y)
{
OLED_WriteCmd(0xb0+y);
OLED_WriteCmd(((x&0xf0)>>4)|0x10);
OLED_WriteCmd((x&0x0f)|0x01);
}
//開啟OLED顯示
void OLED_Display_On(void)
{
OLED_WriteCmd(0X8D); //SET DCDC命令
OLED_WriteCmd(0X14); //DCDC ON
OLED_WriteCmd(0XAF); //DISPLAY ON
}
//關閉OLED顯示
void OLED_Display_Off(void)
{
OLED_WriteCmd(0X8D); //SET DCDC命令
OLED_WriteCmd(0X10); //DCDC OFF
OLED_WriteCmd(0XAE); //DISPLAY OFF
}
//清屏函數,清完屏,整個屏幕是黑色的!和沒點亮一樣!!!
void OLED_Clear(void)
{
unsigned char i,n;
for(i=0;i<8;i++)
{
OLED_WriteCmd (0xb0+i); //設置頁地址（0~7）
OLED_WriteCmd (0x00); //設置顯示位置—列低地址
OLED_WriteCmd (0x10); //設置顯示位置—列高地址
for(n=0;n<128;n++)OLED_Writebyte(0);
} //更新顯示
}
//在指定位置顯示一個字符,包括部分字符
//x:0~127
//y:0~63
//mode:0,反白顯示;1,正常顯示
//size:選擇字體 16/12
void OLED_WriteChar(unsigned char x,unsigned char y,unsigned char chr)
{
unsigned char c=0,i=0;
c=chr-' ';//得到偏移后的值
if(x>127)
{
x=0;
y=y+2;
}
OLED_Set_Pos(x,y);
for(i=0;i<8;i++)
OLED_Writebyte(F8X16[c*16+i]);
OLED_Set_Pos(x,y+1);
for(i=0;i<8;i++)
OLED_Writebyte(F8X16[c*16+i+8]);
}
//m^n函數
unsigned int oled_pow(unsigned char m,unsigned char n)
{
unsigned int result=1;
while(n--)result*=m;
return result;
}
//顯示2個數字
//x,y :起點坐標
//len :數字的位數
//size:字體大小
//mode:模式 0,填充模式;1,疊加模式
//num:數值(0~4294967295);
void OLED_WriteNum1(unsigned char x,unsigned char y,unsigned int num,unsigned char len,unsigned char size2)
{
unsigned char t,temp;
unsigned char enWrite=0;
for(t=0;t<len;t++)
{
temp=(num/oled_pow(10,len-t-1))%10;
if(enWrite==0&&t<(len-1))
{
if(temp==0)
{
OLED_WriteChar(x+(size2/2)*t,y,' ');
continue;
}else enWrite=1;
}
OLED_WriteChar(x+(size2/2)*t,y,temp+'0');
}
}
void OLED_WriteNum2(unsigned char x,unsigned char y,unsigned int num)
{
num=num+0x30;
OLED_WriteChar(x,y,num);
}
//顯示一個字符號串
void OLED_WriteString(unsigned char x,unsigned char y,unsigned char *chr)
{
unsigned char j=0;
while (chr[j]!='\0')
{ OLED_WriteChar(x,y,chr[j]);
x+=8;
if(x>120){x=0;y+=2;}
j++;
}
}
//顯示漢字
void OLED_WriteChinese(unsigned char x,unsigned char y,unsigned char no)
{
unsigned char t,adder=0;
OLED_Set_Pos(x,y);
for(t=0;t<16;t++)
{
OLED_Writebyte(Hzk[2*no][t]);
adder+=1;
}
OLED_Set_Pos(x,y+1);
for(t=0;t<16;t++)
{
OLED_Writebyte(Hzk[2*no+1][t]);
adder+=1;
}
}
/***********功能描述：顯示顯示BMP圖片128×64起始點坐標(x,y),x的范圍0～127，y為頁的范圍0～7*****************/
void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[])
{
unsigned int j=0;
unsigned char x,y;
if(y1%8==0) y=y1/8;
else y=y1/8+1;
for(y=y0;y<y1;y++)
{
OLED_Set_Pos(x0,y);
for(x=x0;x<x1;x++)
{
OLED_Writebyte(BMP[j++]);
}
}
}
//初始化SSD1306
void OLED_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;//定義GPIO結構體
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB, ENABLE); //使能PC,D,G端口時鐘
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_7; //PD3,PD6推挽輸出
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; //推挽輸出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//速度50MHz
GPIO_Init(GPIOA, &GPIO_InitStructure); //初始化GPIOD3,6
GPIO_SetBits(GPIOA,GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_7); //PA3,PA6 輸出高
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1; //PD3,PD6推挽輸出
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; //推挽輸出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//速度50MHz
GPIO_Init(GPIOB, &GPIO_InitStructure); //初始化GPIOD3,6
RES(1);
delay_ms(100);
RES(0);
delay_ms(100);
RES(1);
OLED_WriteCmd(0xAE);//--turn off oled panel
OLED_WriteCmd(0x00);//---set low column address
OLED_WriteCmd(0x10);//---set high column address
OLED_WriteCmd(0x40);//--set start line address Set Mapping RAM Display Start Line (0x00~0x3F)
OLED_WriteCmd(0x81);//--set contrast control register
OLED_WriteCmd(0xCF); // Set SEG Output Current Brightness
OLED_WriteCmd(0xA1);//--Set SEG/Column Mapping 0xa0左右反置 0xa1正常
OLED_WriteCmd(0xC8);//Set COM/Row Scan Direction 0xc0上下反置 0xc8正常
OLED_WriteCmd(0xA6);//--set normal display
OLED_WriteCmd(0xA8);//--set multiplex ratio(1 to 64)
OLED_WriteCmd(0x3f);//--1/64 duty
OLED_WriteCmd(0xD3);//-set display offset Shift Mapping RAM Counter (0x00~0x3F)
OLED_WriteCmd(0x00);//-not offset
OLED_WriteCmd(0xd5);//--set display clock divide ratio/oscillator frequency
OLED_WriteCmd(0x80);//--set divide ratio, Set Clock as 100 Frames/Sec
OLED_WriteCmd(0xD9);//--set pre-charge period
OLED_WriteCmd(0xF1);//Set Pre-Charge as 15 Clocks & Discharge as 1 Clock
OLED_WriteCmd(0xDA);//--set com pins hardware configuration
OLED_WriteCmd(0x12);
OLED_WriteCmd(0xDB);//--set vcomh
OLED_WriteCmd(0x40);//Set VCOM Deselect Level
OLED_WriteCmd(0x20);//-Set Page Addressing Mode (0x00/0x01/0x02)
OLED_WriteCmd(0x02);//
OLED_WriteCmd(0x8D);//--set Charge Pump enable/disable
OLED_WriteCmd(0x14);//--set(0x10) disable
OLED_WriteCmd(0xA4);// Disable Entire Display On (0xa4/0xa5)
OLED_WriteCmd(0xA6);// Disable Inverse Display On (0xa6/a7)
OLED_WriteCmd(0xAF);//--turn on oled panel
OLED_WriteCmd(0xAF); /*display ON*/
OLED_Clear();
OLED_Set_Pos(0,0);
}
void CS(unsigned char i)
{
if(i==0)
{
GPIO_ResetBits(GPIOA,GPIO_Pin_4); //CS(0)
}
if(i==1)
{
GPIO_SetBits(GPIOA,GPIO_Pin_4);
}
}
void DC(unsigned char i)
{
if(i==0)
{
GPIO_ResetBits(GPIOB,GPIO_Pin_1); //CS(0)
}
if(i==1)
{
GPIO_SetBits(GPIOB,GPIO_Pin_1);
}
}
void RES(unsigned char i)
{
if(i==0)
{
GPIO_ResetBits(GPIOB,GPIO_Pin_0); //CS(0)
}
if(i==1)
{
GPIO_SetBits(GPIOB,GPIO_Pin_0);
}
}
void DIN(unsigned char i)
{
if(i==0)
{
GPIO_ResetBits(GPIOA,GPIO_Pin_7); //CS(0)
}
if(i==1)
{
GPIO_SetBits(GPIOA,GPIO_Pin_7);
}
}
void SCL(unsigned char i)
{
if(i==0)
{
GPIO_ResetBits(GPIOA,GPIO_Pin_5); //CS(0)
}
if(i==1)
{
GPIO_SetBits(GPIOA,GPIO_Pin_5);
}
}

復制代碼

全部資料下載：

OLED驅動.zip (7.63 KB, 下載次數: 132)

ID:124921 · 發表于 2016-6-4 10:08

大家頂起來

ID:82944 · 發表于 2016-7-25 22:50

寫的不錯很好值得參考

ID:112693 · 發表于 2017-1-17 10:24

學習了.......................................

ID:167757 · 發表于 2017-3-2 20:53

再來一個吧啊吧

ID:190909 · 發表于 2017-4-18 17:32

正好需要，學習一下

ID:206664 · 發表于 2017-6-1 12:26

為什么我一次性將圖片刷入ram區，屏幕會有閃動呢？

ID:208667 · 發表于 2017-6-7 08:57

非常感謝。

ID:208667 · 發表于 2017-6-7 08:58

實現動畫顯示效果，這么難不？

ID:219080 · 發表于 2017-7-12 11:27

學習了謝謝樓主

ID:281751 · 發表于 2018-3-5 15:57

謝謝樓主分享!

帳號		自動登錄	找回密碼
密碼			立即注冊

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

STM32的OLED驅動