現在問題是,上電能顯示654321,可當按下P1.3口接的按鍵時,6 個數碼管都不會亮了,程序哪里出了問題

程序目的:上電時數碼管顯示654321,每次按下P1.3口按鍵時
        對31H中的數據加一,加到 10時,31H中清0并對下一個地址
        (32H)中的數據加1,依次類推
  *************************************************************

org 0000h
 jmp start
 org 0003h
 reti
 org 000bh
 reti
 org 0013h
jmp wzd1
 org 001bh
 reti
 org 0023h
 reti


 wzd1: push psw      ;外中斷入口
       push acc
       clr ea
       clr ex1
       jnb p1.3,key3    ;P1.3為0時轉KEY3
 wzdfh:pop acc          ;外中斷返回
       pop psw
       setb ea
       setb ex1
      reti
 key3:call delay10ms
     jb p1.3,wzdfh
    l1: jnb p1.3,$
       inc 31h           ;P1.3松開時31H加1
     mov a,#10
     cjne a,31h,wzdfh     ;31H中不等于10中斷返回
     clr a
     mov 31h,a             ;31H中的數據清0并對下一地址中的數據加一
     inc 32h
     mov a,#10
     cjne a,32h,wzdfh
      clr a
     mov 32h,a
     inc 33h
     mov a,#10
     cjne a,33h,wzdfh
          clr a
     mov 33h,a
     inc 34h
     mov a,#10
     cjne a,34h,wzdfh
          clr a
     mov 34h,a
     inc 35h
     mov a,#10
     cjne a,35h,wzdfh
          clr a
     mov 35h,a
     inc 36h
     mov a,#10
     cjne a,36h,wzdfh
     clr a
     mov 36h,a
     jmp wzdfh

 start:mov 31h,#1
       mov 32h,#2
       mov 33h,#3
       mov 34h,#4
       mov 35h,#5
       mov 36h,#6
       clr p1.5
       setb ea
        setb ex1
 start1:call display
       jmp start1
display:mov r1,#31h
   mov r2,#00000001
play:  mov p0,#0ffh
       mov a,r2
       mov p2,a
       mov a,@r1
       mov dptr,#tab
       movc a,@a+dptr
       mov p0,a
       call delay1ms
       inc r1
       mov a,p2
       jb acc.5,endout
       rl a
       mov r2,a
       mov p2,#0h
       jmp play
endout:mov p0,#0ffh
       mov p2,#0
       ret
delay1ms:mov r3,#2
   d1:   mov r4,#250
   d2:   djnz r4,$
         djnz r3,d1
         ret
delay10ms: call play   ;10ms子程序,調用一次顯示子程序約6ms,調兩次約12ms
           call play
         ret

tab:db   48h,0ebh,52h,62h,0e1h,64h,44h,0eah,40h,60h
end

哎~~

我也是開始學匯編，現在開始學C了~~~