ADS8681 STM32的SPI驅動代碼 vscode僅供參考

ID:1020393 · 發表于 2022-4-21 16:20

單片機源程序如下:

#include "ads8681.h"
#include "stm32f1xx_hal_def.h"
/**
* @brief SPI發送指定長度的數據
* @param buf —— 發送數據緩沖區首地址
* @param size —— 要發送數據的字節數
* @retval 成功返回HAL_OK
*/
// static HAL_StatusTypeDef SPI_Transmit(uint8_t* send_buf, uint16_t size)
// {
// return HAL_SPI_Transmit(&hspi1, send_buf, size, 100);
// }
/**
* @brief SPI接收指定長度的數據
* @param buf —— 接收數據緩沖區首地址
* @param size —— 要接收數據的字節數
* @retval 成功返回HAL_OK
*/
// static HAL_StatusTypeDef SPI_Receive(uint8_t* recv_buf, uint16_t size)
// {
// return HAL_SPI_Receive(&hspi1, recv_buf, size, 100);
// }
/**
* @brief SPI在發送數據的同時接收指定長度的數據
* @param send_buf —— 接收數據緩沖區首地址
* @param recv_buf —— 接收數據緩沖區首地址
* @param size —— 要發送/接收數據的字節數
* @retval 成功返回HAL_OK
*/
static HAL_StatusTypeDef SPI_TransmitReceive(uint8_t* send_buf, uint8_t* recv_buf, uint16_t size)
{
return HAL_SPI_TransmitReceive(&hspi1, send_buf, recv_buf, size, 100);
}
/**
* @brief ADS8681_Read_Write_Byte ———— ADS8681讀寫一個字節
* @param dat —— 發送數據緩沖區
* @param read_byte —— 接收數據緩沖區首地址
* @retval read_byte
*/
uint8_t ADS8681_Read_Write_Byte(uint8_t dat)
{
uint8_t read_byte;
ADC_CS_L;
SPI_TransmitReceive(&dat, &read_byte,1);
ADC_CS_H;
return read_byte ;
}
/**
* @brief ADS8681_Read_Write_16Byte ——— ADS8681讀寫16位數據
* @param dat —— 發送數據
* @param write_buff —— 接收數據緩沖區首地址
* @param read_buff —— 接收數據緩沖區首地址
* @retval read_byte
*/
uint16_t ADS8681_Read_Write_16Byte(uint16_t dat)
{
uint16_t read_byte;
uint8_t write_buff[2];
uint8_t read_buff[2];
write_buff[0] = (dat>>8)&0xff;
write_buff[1] = dat&0xff;
ADC_CS_L;
SPI_TransmitReceive(write_buff, read_buff,2);
ADC_CS_H;
read_byte = read_buff[0];
read_byte = ((read_byte<<8)&0xff00)|read_buff[1];
return read_byte;
}
/**
* @brief aADS8681_reg_config ——— ADS8681操作寄存器，寫數據，讀數據
* @param com —— 命令字（前7位為 List of Input Commands）
* @param addrs —— 寄存器的地址（8-16位為Configuration Registers）
* @param dat —— 寄存器的15-0位（17-32位為Configuration Registers數據位）
* @retval result
*/
uint32_t ADS8681_reg_config(uint8_t com,uint16_t address,uint16_t dat)
{
uint32_t result = 0;
uint16_t temp = 0;
ADC_CS_L;
temp =(((com << 1) | ((address >> 8) & 1)) << 8) | (address & 0x00FF); //com和 address
result = ADS8681_Read_Write_16Byte(temp);
result = (result<<16)|ADS8681_Read_Write_16Byte(dat);
ADC_CS_H;
return result;
}
/**
* @brief ADS8681_Read ——— ADS8681讀數據，一次讀32位
* @retval read_buff
*/
uint32_t ADS8681_Read(void)
{
unsigned long read_buff = 0;
ADC_CS_L;
read_buff = ((read_buff<<16)&0xffff0000)|ADS8681_Read_Write_16Byte(DUMMY);
ADC_CS_H;
return read_buff;
}
void ads8681_Init(void)
{
ADS_RST_L;
ADS_RVS_L;
HAL_Delay(100);
ADS_RST_H;
ADS8681_reg_config(0,0,0x00); //
}
void ADS8681_Display(void)
{
unsigned long temp1=0,temp=0;
//采樣5000次，去ADC抖動
for (uint16_t i = 0; i <5000; i++)
{
temp1 = (unsigned long)ADS8681_Read();
temp = temp+temp1;
}
//ADC采樣轉換結果
temp = temp/5000;
temp = (temp-32767)*24576; // 轉換結公式 V=(采樣結果-32767)*最大量程/65535
temp = temp/65535*10;
OLED_ShowNum(41,2,temp,5,16);
}