關于CC1101遙控距離程序調試問題附單片機程序

ID:421668 · 發表于 2022-3-23 09:17

如題，我用了兩個CC1101模塊做收發遙控，然后發射功率我設置到了最大，可是空曠距離很不理想。我看手冊上說怎么也得200米，可是我的只有二三十米的樣子，論壇的友友們，幫忙指點一下我的程序看看是不是哪里還是設置的不對啊。CC1101我買的現成模塊，硬件電路應該沒有問題。我也懷疑問題出在我的程序里面。
單片機程序如下：

#include <reg52.h>
#include <intrins.h>
#define INT8U unsigned char
#define uchar unsigned char
#define INT16U unsigned int
#define uint unsigned int
sfr P3M1=0xb1;
sfr P3M0=0xb2;
sfr P2M1=0x95;
sfr P2M0=0x96;
sfr P1M1=0x91;
sfr P1M0=0x92;
#define ID_ADDR_ROM 0x1ff9
#define ID_ADDR_RAM 0xf1
#define BAUD 0XFD00 //9600bps @11.0592Mhz
sfr IAP_DATA=0xc2;
sfr IAP_ADDRH=0xc3;
sfr IAP_ADDRL=0xc4;
sfr IAP_CMD=0xc5;
sfr IAP_TRIG=0xc6;
sfr IAP_CONTR=0xc7;
#define ENABLE_IAP 0x82
#define IAP_ADDRESS 0x0000//前512字節
#define IAP_ADDRESS2 0x0200//后512字節
#define CMD_IDLE 0
#define CMD_READ 1
#define CMD_PROGRAM 2
#define CMD_ERASE 3
INT8U id[7]={0},flag_study=0;
#define HEAD_LEN 6
#define WRITE_BURST 0x40 //連續寫入
#define READ_SINGLE 0x80 //讀
#define READ_BURST 0xC0 //連續讀
#define BYTES_IN_RXFIFO 0x7F //接收緩沖區的有效字節數
#define CRC_OK 0x80 //CRC校驗通過位標志
//*****************************************************************************************
//sbit GDO0 =P3^3;
//sbit GDO2 =P3^2;
//sbit MISO =P1^4;
//sbit MOSI =P1^3;
//sbit SCK =P1^5;
//sbit CSN =P2^6;
sbit GDO0 =P2^7;
sbit GDO2 =P3^2;
sbit MISO =P1^4;
sbit MOSI =P1^3;
sbit SCK =P1^5;
sbit CSN =P1^0;
sbit CSN2 =P1^0;
//*****************************************************************************************
//sbit KEY_start =P2^2; //對應KEY2 啟動按鍵
//sbit KEY_stop =P2^0;//對應KEY0 停止按鍵
//sbit KEY_up =P2^1; //對應KEY1 上升按鍵
//sbit KEY_down =P2^3;//對應KEY3 下降按鍵
//sbit KEY_left =P3^6;//對應KEY6 按鍵外部中斷2
//sbit KEY_right =P3^7;//對應KEY5 按鍵外部中斷3
//sbit key4 = P2^4;
//sbit key5 = P3^7;
//sbit key6 = P3^6;
//sbit key7 = P3^5;
sbit KEY0 =P2^0;//停止
sbit KEY1 =P2^1;//上升
sbit KEY2 =P2^2;//啟動
sbit KEY3 =P2^3;//下降
//*****************************************************************************************
sbit led1=P2^5; //指示燈LED1，低電平時亮，高電平時暗紅燈
sbit led2=P2^4; //指示燈LED1，低電平時亮，高電平時暗綠燈
unsigned char key_up=1,key_down;
unsigned char num;
//***************更多功率參數設置可詳細參考DATACC1100英文文檔中第48-49頁的參數表************
//INT8U PaTabel[8] = {0x04 ,0x04 ,0x04 ,0x04 ,0x04 ,0x04 ,0x04 ,0x04}; //-30dBm 功率最小
//INT8U PaTabel[8] = {0x60 ,0x60 ,0x60 ,0x60 ,0x60 ,0x60 ,0x60 ,0x60}; //0dBm
INT8U PaTabel[8] = {0xC0 ,0xC0 ,0xC0 ,0xC0 ,0xC0 ,0xC0 ,0xC0 ,0xC0}; //10dBm 功率最大
//INT8U PaTabel[8] = {0xC0 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00}; //10dBm 功率最大
//*****************************************************************************************
void SpiInit(void);
void CpuInit(void);
void RESET_CC1100(void);
void POWER_UP_RESET_CC1100(void);
void halSpiWriteReg(INT8U addr, INT8U value);
void halSpiWriteBurstReg(INT8U addr, INT8U *buffer, INT8U count);
void halSpiStrobe(INT8U strobe);
INT8U halSpiReadReg(INT8U addr);
void halSpiReadBurstReg(INT8U addr, INT8U *buffer, INT8U count);
INT8U halSpiReadStatus(INT8U addr);
void halRfWriteRfSettings(void);
void halRfSendPacket(INT8U *txBuffer, INT8U size);
INT8U halRfReceivePacket(INT8U *rxBuffer, INT8U *length);
//*****************************************************************************************
// CC1100 STROBE, CONTROL AND STATUS REGSITER
#define CCxxx0_IOCFG2 0x00 // GDO2 output pin configuration
#define CCxxx0_IOCFG1 0x01 // GDO1 output pin configuration
#define CCxxx0_IOCFG0 0x02 // GDO0 output pin configuration
#define CCxxx0_FIFOTHR 0x03 // RX FIFO and TX FIFO thresholds
#define CCxxx0_SYNC1 0x04 // Sync word, high INT8U
#define CCxxx0_SYNC0 0x05 // Sync word, low INT8U
#define CCxxx0_PKTLEN 0x06 // Packet length
#define CCxxx0_PKTCTRL1 0x07 // Packet automation control
#define CCxxx0_PKTCTRL0 0x08 // Packet automation control
#define CCxxx0_ADDR 0x09 // Device address
#define CCxxx0_CHANNR 0x0A // Channel number
#define CCxxx0_FSCTRL1 0x0B // Frequency synthesizer control
#define CCxxx0_FSCTRL0 0x0C // Frequency synthesizer control
#define CCxxx0_FREQ2 0x0D // Frequency control word, high INT8U
#define CCxxx0_FREQ1 0x0E // Frequency control word, middle INT8U
#define CCxxx0_FREQ0 0x0F // Frequency control word, low INT8U
#define CCxxx0_MDMCFG4 0x10 // Modem configuration
#define CCxxx0_MDMCFG3 0x11 // Modem configuration
#define CCxxx0_MDMCFG2 0x12 // Modem configuration
#define CCxxx0_MDMCFG1 0x13 // Modem configuration
#define CCxxx0_MDMCFG0 0x14 // Modem configuration
#define CCxxx0_DEVIATN 0x15 // Modem deviation setting
#define CCxxx0_MCSM2 0x16 // Main Radio Control State Machine configuration
#define CCxxx0_MCSM1 0x17 // Main Radio Control State Machine configuration
#define CCxxx0_MCSM0 0x18 // Main Radio Control State Machine configuration
#define CCxxx0_FOCCFG 0x19 // Frequency Offset Compensation configuration
#define CCxxx0_BSCFG 0x1A // Bit Synchronization configuration
#define CCxxx0_AGCCTRL2 0x1B // AGC control
#define CCxxx0_AGCCTRL1 0x1C // AGC control
#define CCxxx0_AGCCTRL0 0x1D // AGC control
#define CCxxx0_WOREVT1 0x1E // High INT8U Event 0 timeout
#define CCxxx0_WOREVT0 0x1F // Low INT8U Event 0 timeout
#define CCxxx0_WORCTRL 0x20 // Wake On Radio control
#define CCxxx0_FREND1 0x21 // Front end RX configuration
#define CCxxx0_FREND0 0x22 // Front end TX configuration
#define CCxxx0_FSCAL3 0x23 // Frequency synthesizer calibration
#define CCxxx0_FSCAL2 0x24 // Frequency synthesizer calibration
#define CCxxx0_FSCAL1 0x25 // Frequency synthesizer calibration
#define CCxxx0_FSCAL0 0x26 // Frequency synthesizer calibration
#define CCxxx0_RCCTRL1 0x27 // RC oscillator configuration
#define CCxxx0_RCCTRL0 0x28 // RC oscillator configuration
#define CCxxx0_FSTEST 0x29 // Frequency synthesizer calibration control
#define CCxxx0_PTEST 0x2A // Production test
#define CCxxx0_AGCTEST 0x2B // AGC test
#define CCxxx0_TEST2 0x2C // Various test settings
#define CCxxx0_TEST1 0x2D // Various test settings
#define CCxxx0_TEST0 0x2E // Various test settings
// Strobe commands
#define CCxxx0_SRES 0x30 // Reset chip.
#define CCxxx0_SFSTXON 0x31 // Enable and calibrate frequency synthesizer (if MCSM0.FS_AUTOCAL=1).
// If in RX/TX: Go to a wait state where only the synthesizer is
// running (for quick RX / TX turnaround).
#define CCxxx0_SXOFF 0x32 // Turn off crystal oscillator.
#define CCxxx0_SCAL 0x33 // Calibrate frequency synthesizer and turn it off
// (enables quick start).
#define CCxxx0_SRX 0x34 // Enable RX. Perform calibration first if coming from IDLE and
// MCSM0.FS_AUTOCAL=1.
#define CCxxx0_STX 0x35 // In IDLE state: Enable TX. Perform calibration first if
// MCSM0.FS_AUTOCAL=1. If in RX state and CCA is enabled:
// Only go to TX if channel is clear.
#define CCxxx0_SIDLE 0x36 // Exit RX / TX, turn off frequency synthesizer and exit
// Wake-On-Radio mode if applicable.
#define CCxxx0_SAFC 0x37 // Perform AFC adjustment of the frequency synthesizer
#define CCxxx0_SWOR 0x38 // Start automatic RX polling sequence (Wake-on-Radio)
#define CCxxx0_SPWD 0x39 // Enter power down mode when CSn goes high.
#define CCxxx0_SFRX 0x3A // Flush the RX FIFO buffer.
#define CCxxx0_SFTX 0x3B // Flush the TX FIFO buffer.
#define CCxxx0_SWORRST 0x3C // Reset real time clock.
#define CCxxx0_SNOP 0x3D // No operation. May be used to pad strobe commands to two
// INT8Us for simpler software.
#define CCxxx0_PARTNUM 0x30
#define CCxxx0_VERSION 0x31
#define CCxxx0_FREQEST 0x32
#define CCxxx0_LQI 0x33
#define CCxxx0_RSSI 0x34
#define CCxxx0_MARCSTATE 0x35
#define CCxxx0_WORTIME1 0x36
#define CCxxx0_WORTIME0 0x37
#define CCxxx0_PKTSTATUS 0x38
#define CCxxx0_VCO_VC_DAC 0x39
#define CCxxx0_TXBYTES 0x3A
#define CCxxx0_RXBYTES 0x3B
#define CCxxx0_PATABLE 0x3E
#define CCxxx0_TXFIFO 0x3F
#define CCxxx0_RXFIFO 0x3F
// RF_SETTINGS is a data structure which contains all relevant CCxxx0 registers
typedef struct S_RF_SETTINGS
{
INT8U FSCTRL2; //自已加的
INT8U FSCTRL1; // Frequency synthesizer control.
INT8U FSCTRL0; // Frequency synthesizer control.
INT8U FREQ2; // Frequency control word, high INT8U.
INT8U FREQ1; // Frequency control word, middle INT8U.
INT8U FREQ0; // Frequency control word, low INT8U.
INT8U MDMCFG4; // Modem configuration.
INT8U MDMCFG3; // Modem configuration.
INT8U MDMCFG2; // Modem configuration.
INT8U MDMCFG1; // Modem configuration.
INT8U MDMCFG0; // Modem configuration.
INT8U CHANNR; // Channel number.
INT8U DEVIATN; // Modem deviation setting (when FSK modulation is enabled).
INT8U FREND1; // Front end RX configuration.
INT8U FREND0; // Front end RX configuration.
INT8U MCSM0; // Main Radio Control State Machine configuration.
INT8U FOCCFG; // Frequency Offset Compensation Configuration.
INT8U BSCFG; // Bit synchronization Configuration.
INT8U AGCCTRL2; // AGC control.
INT8U AGCCTRL1; // AGC control.
INT8U AGCCTRL0; // AGC control.
INT8U FSCAL3; // Frequency synthesizer calibration.
INT8U FSCAL2; // Frequency synthesizer calibration.
INT8U FSCAL1; // Frequency synthesizer calibration.
INT8U FSCAL0; // Frequency synthesizer calibration.
INT8U FSTEST; // Frequency synthesizer calibration control
INT8U TEST2; // Various test settings.
INT8U TEST1; // Various test settings.
INT8U TEST0; // Various test settings.
INT8U IOCFG2; // GDO2 output pin configuration
INT8U IOCFG0; // GDO0 output pin configuration
INT8U PKTCTRL1; // Packet automation control.
INT8U PKTCTRL0; // Packet automation control.
INT8U ADDR; // Device address.
INT8U PKTLEN; // Packet length.
} RF_SETTINGS;
/////////////////////////////////////////////////////////////////
const RF_SETTINGS rfSettings =
{
0x00,
0x08, // FSCTRL1 Frequency synthesizer control.
0x00, // FSCTRL0 Frequency synthesizer control.
0x10, // FREQ2 Frequency control word, high byte.
0xA7, // FREQ1 Frequency control word, middle byte.
0x62, // FREQ0 Frequency control word, low byte.
// 0x5B, // MDMCFG4 Modem configuration.
// 0xF8, // MDMCFG3 Modem configuration.
0x5B, // MDMCFG4
0xE4, // MDMCFG3
0x03, // MDMCFG2 Modem configuration.
0x22, // MDMCFG1 Modem configuration.
0xF8, // MDMCFG0 Modem configuration.
0x00, // CHANNR Channel number.
0x47, // DEVIATN Modem deviation setting (when FSK modulation is enabled).
0xB6, // FREND1 Front end RX configuration.
0x10, // FREND0 Front end RX configuration.
0x18, // MCSM0 Main Radio Control State Machine configuration.
0x1D, // FOCCFG Frequency Offset Compensation Configuration.
0x1C, // BSCFG Bit synchronization Configuration.
0xC7, // AGCCTRL2 AGC control.
0x00, // AGCCTRL1 AGC control.
0xB2, // AGCCTRL0 AGC control.
0xEA, // FSCAL3 Frequency synthesizer calibration.
0x2A, // FSCAL2 Frequency synthesizer calibration.
0x00, // FSCAL1 Frequency synthesizer calibration.
0x11, // FSCAL0 Frequency synthesizer calibration.
0x59, // FSTEST Frequency synthesizer calibration.
0x81, // TEST2 Various test settings.
0x35, // TEST1 Various test settings.
0x09, // TEST0 Various test settings.
0x0B, // IOCFG2 GDO2 output pin configuration.
0x06, // IOCFG0D GDO0 output pin configuration. Refer to SmartRF?Studio User Manual for detailed pseudo register explanation.
0x04, // PKTCTRL1 Packet automation control.
0x05, // PKTCTRL0 Packet automation control.
0x00, // ADDR Device address.
0x0c // PKTLEN Packet length.
};
//*****************************************************************************************
//函數名：delay(unsigned int s)
//輸入：時間
//輸出：無
//功能描述：普通廷時,內部用
//*****************************************************************************************
static void delay(unsigned int s)
{
unsigned int i;
for(i=0; i<s; i++);
for(i=0; i<s; i++);
}
void delay1ms(int t)//誤差0.434028 us
{
unsigned char i=0,j=0,m=0;
for(m=t;m>0;m--)
for(i=55;i>0;i--)
for(j=53;j>0;j--);
}
void delay1s(uchar t)//誤差1.000000 us
{//6倍速
unsigned char i=0,j=0,k=0,m=0;
for(m=t;m>0;m--)
for(i=66;i>0;i--)
for(j=218;j>0;j--)
for(k=207;k>0;k--);
}
void delay12us()//誤差0.234375 us
{
unsigned char i=0;
for(i=33;i>0;i--);
}
void IapIdle()
{
IAP_CONTR=0;//關閉IAP功能
IAP_CMD=0;//清除命令寄存器
IAP_TRIG=0;//清除觸發寄存器
IAP_ADDRH=0x80;//將地址設置到非IAP區域
IAP_ADDRL=0;
}
uchar IapReadByte(uint addr)
{
uchar dat;
IAP_CONTR=ENABLE_IAP;//使能IAP
IAP_CMD=CMD_READ;//設置IAP命令
IAP_ADDRL=addr;//設置IAP低地址
IAP_ADDRH=addr>>8;//設置IAP高地址
IAP_TRIG=0x5a;//寫觸發命令
IAP_TRIG=0xa5;
_nop_();//等待操作完成
dat=IAP_DATA;//讀數據
IapIdle();
return dat;
}
void IapProgramByte(uint addr,uchar dat)
{
IAP_CONTR=ENABLE_IAP;//使能IAP
IAP_CMD=CMD_PROGRAM;//設置IAP命令
IAP_ADDRL=addr;//設置IAP低地址
IAP_ADDRH=addr>>8;//設置IAP高地址
IAP_DATA=dat;//寫IAP數據
IAP_TRIG=0x5a;//寫觸發命令
IAP_TRIG=0xa5;
_nop_();//等待操作完成
IapIdle();
}
void IapEraseSector(uint addr)
{
IAP_CONTR=ENABLE_IAP;//使能IAP
IAP_CMD=CMD_ERASE;//設置IAP命令
IAP_ADDRL=addr;//設置低地址
IAP_ADDRH=addr>>8;//設置高地址
IAP_TRIG=0x5a;//寫觸發命令
IAP_TRIG=0xa5;
_nop_();//等待操作完成
IapIdle();
}
void SaveData(uchar *dat,uchar len)
{
uchar i=0;
IapEraseSector(IAP_ADDRESS);
for(i=0;i<len;i++)
{
IapProgramByte(IAP_ADDRESS+i,dat[i]);
delay1ms(1);
}
}
void halWait(INT16U timeout) {
do {
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
} while (--timeout);
}
void SpiInit(void)
{
CSN=0;
SCK=0;
CSN=1;
}
/*****************************************************************************************
//函數名：CpuInit()
//輸入：無
//輸出：無
//功能描述：SPI初始化程序
/*****************************************************************************************/
void CpuInit(void)
{
SpiInit();
delay(5000);
}
//*****************************************************************************************
//函數名：SpisendByte(INT8U dat)
//輸入：發送的數據
//輸出：無
//功能描述：SPI發送一個字節
//*****************************************************************************************
INT8U SpiTxRxByte(INT8U dat)
{
INT8U i,temp;
temp = 0;
SCK = 0;
for(i=0; i<8; i++)
{
if(dat & 0x80)
{
MOSI = 1;
}
else MOSI = 0;
dat <<= 1;
SCK = 1;
_nop_();
_nop_();
temp <<= 1;
if(MISO)temp++;
SCK = 0;
_nop_();
_nop_();
}
return temp;
}
//*****************************************************************************************
//函數名：void RESET_CC1100(void)
//輸入：無
//輸出：無
//功能描述：復位CC1100
//*****************************************************************************************
void RESET_CC1100(void)
{
CSN = 0;
while (MISO);
SpiTxRxByte(CCxxx0_SRES); //寫入復位命令
while (MISO);
CSN = 1;
}
//*****************************************************************************************
//函數名：void POWER_UP_RESET_CC1100(void)
//輸入：無
//輸出：無
//功能描述：上電復位CC1100
//*****************************************************************************************
void POWER_UP_RESET_CC1100(void)
{
CSN = 1;
halWait(1);
CSN = 0;
halWait(1);
CSN = 1;
halWait(41);
RESET_CC1100(); //復位CC1100
}
//*****************************************************************************************
//函數名：void halSpiWriteReg(INT8U addr, INT8U value)
//輸入：地址和配置字
//輸出：無
//功能描述：SPI寫寄存器
//*****************************************************************************************
void halSpiWriteReg(INT8U addr, INT8U value)
{
CSN = 0;
while (MISO);
SpiTxRxByte(addr); //寫地址
SpiTxRxByte(value); //寫入配置
CSN = 1;
}
//*****************************************************************************************
//函數名：void halSpiWriteBurstReg(INT8U addr, INT8U *buffer, INT8U count)
//輸入：地址，寫入緩沖區，寫入個數
//輸出：無
//功能描述：SPI連續寫配置寄存器
//*****************************************************************************************
void halSpiWriteBurstReg(INT8U addr, INT8U *buffer, INT8U count)
{
INT8U i, temp;
temp = addr | WRITE_BURST;
CSN = 0;
while (MISO);
SpiTxRxByte(temp);
for (i = 0; i < count; i++)
{
SpiTxRxByte(buffer[i]);
}
CSN = 1;
}
//*****************************************************************************************
//函數名：void halSpiStrobe(INT8U strobe)
//輸入：命令
//輸出：無
//功能描述：SPI寫命令
//*****************************************************************************************
void halSpiStrobe(INT8U strobe)
{
CSN = 0;
while (MISO);
SpiTxRxByte(strobe); //寫入命令
CSN = 1;
}
//*****************************************************************************************
//函數名：INT8U halSpiReadReg(INT8U addr)
//輸入：地址
//輸出：該寄存器的配置字
//功能描述：SPI讀寄存器
//*****************************************************************************************
INT8U halSpiReadReg(INT8U addr)
{
INT8U temp, value;
temp = addr|READ_SINGLE;//讀寄存器命令
CSN = 0;
while (MISO);
SpiTxRxByte(temp);
value = SpiTxRxByte(0);
CSN = 1;
return value;
}
//*****************************************************************************************
//函數名：void halSpiReadBurstReg(INT8U addr, INT8U *buffer, INT8U count)
//輸入：地址，讀出數據后暫存的緩沖區，讀出配置個數
//輸出：無
//功能描述：SPI連續寫配置寄存器
//*****************************************************************************************
void halSpiReadBurstReg(INT8U addr, INT8U *buffer, INT8U count)
{
INT8U i,temp;
temp = addr | READ_BURST; //寫入要讀的配置寄存器地址和讀命令
CSN = 0;
while (MISO);
SpiTxRxByte(temp);
for (i = 0; i < count; i++)
{
buffer[i] = SpiTxRxByte(0);
}
CSN = 1;
}
//*****************************************************************************************
//函數名：INT8U halSpiReadReg(INT8U addr)
//輸入：地址
//輸出：該狀態寄存器當前值
//功能描述：SPI讀狀態寄存器
//*****************************************************************************************
INT8U halSpiReadStatus(INT8U addr)
{
INT8U value,temp;
temp = addr | READ_BURST; //寫入要讀的狀態寄存器的地址同時寫入讀命令
CSN = 0;
while (MISO);
SpiTxRxByte(temp);
value = SpiTxRxByte(0);
CSN = 1;
return value;
}
//*****************************************************************************************
//函數名：void halRfWriteRfSettings(RF_SETTINGS *pRfSettings)
//輸入：無
//輸出：無
//功能描述：配置CC1100的寄存器
//*****************************************************************************************
void halRfWriteRfSettings(void)
{
halSpiWriteReg(CCxxx0_FSCTRL0, rfSettings.FSCTRL2);//自已加的
// Write register settings
halSpiWriteReg(CCxxx0_FSCTRL1, rfSettings.FSCTRL1);
halSpiWriteReg(CCxxx0_FSCTRL0, rfSettings.FSCTRL0);
halSpiWriteReg(CCxxx0_FREQ2, rfSettings.FREQ2);
halSpiWriteReg(CCxxx0_FREQ1, rfSettings.FREQ1);
halSpiWriteReg(CCxxx0_FREQ0, rfSettings.FREQ0);
halSpiWriteReg(CCxxx0_MDMCFG4, rfSettings.MDMCFG4);
halSpiWriteReg(CCxxx0_MDMCFG3, rfSettings.MDMCFG3);
halSpiWriteReg(CCxxx0_MDMCFG2, rfSettings.MDMCFG2);
halSpiWriteReg(CCxxx0_MDMCFG1, rfSettings.MDMCFG1);
halSpiWriteReg(CCxxx0_MDMCFG0, rfSettings.MDMCFG0);
halSpiWriteReg(CCxxx0_CHANNR, rfSettings.CHANNR);
halSpiWriteReg(CCxxx0_DEVIATN, rfSettings.DEVIATN);
halSpiWriteReg(CCxxx0_FREND1, rfSettings.FREND1);
halSpiWriteReg(CCxxx0_FREND0, rfSettings.FREND0);
halSpiWriteReg(CCxxx0_MCSM0 , rfSettings.MCSM0 );
halSpiWriteReg(CCxxx0_FOCCFG, rfSettings.FOCCFG);
halSpiWriteReg(CCxxx0_BSCFG, rfSettings.BSCFG);
halSpiWriteReg(CCxxx0_AGCCTRL2, rfSettings.AGCCTRL2);
halSpiWriteReg(CCxxx0_AGCCTRL1, rfSettings.AGCCTRL1);
halSpiWriteReg(CCxxx0_AGCCTRL0, rfSettings.AGCCTRL0);
halSpiWriteReg(CCxxx0_FSCAL3, rfSettings.FSCAL3);
halSpiWriteReg(CCxxx0_FSCAL2, rfSettings.FSCAL2);
halSpiWriteReg(CCxxx0_FSCAL1, rfSettings.FSCAL1);
halSpiWriteReg(CCxxx0_FSCAL0, rfSettings.FSCAL0);
halSpiWriteReg(CCxxx0_FSTEST, rfSettings.FSTEST);
halSpiWriteReg(CCxxx0_TEST2, rfSettings.TEST2);
halSpiWriteReg(CCxxx0_TEST1, rfSettings.TEST1);
halSpiWriteReg(CCxxx0_TEST0, rfSettings.TEST0);
halSpiWriteReg(CCxxx0_IOCFG2, rfSettings.IOCFG2);
halSpiWriteReg(CCxxx0_IOCFG0, rfSettings.IOCFG0);
halSpiWriteReg(CCxxx0_PKTCTRL1, rfSettings.PKTCTRL1);
halSpiWriteReg(CCxxx0_PKTCTRL0, rfSettings.PKTCTRL0);
halSpiWriteReg(CCxxx0_ADDR, rfSettings.ADDR);
halSpiWriteReg(CCxxx0_PKTLEN, rfSettings.PKTLEN);
}
//*****************************************************************************************
//函數名：void halRfSendPacket(INT8U *txBuffer, INT8U size)
//輸入：發送的緩沖區，發送數據個數
//輸出：無
//功能描述：CC1100發送一組數據
//*****************************************************************************************
void halRfSendPacket(INT8U *txBuffer, INT8U size)
{
halSpiWriteReg(CCxxx0_TXFIFO, size);
halSpiWriteBurstReg(CCxxx0_TXFIFO, txBuffer, size); //寫入要發送的數據
halSpiStrobe(CCxxx0_STX); //進入發送模式發送數據
// Wait for GDO0 to be set -> sync transmitted
while (!GDO0);
// Wait for GDO0 to be cleared -> end of packet
while (GDO0);
// led1=1;
halSpiStrobe(CCxxx0_SFTX);
}
void setRxMode(void)
{
halSpiStrobe(CCxxx0_SRX); //進入接收狀態
}
/*
// Bit masks corresponding to STATE[2:0] in the status byte returned on MISO
#define CCxx00_STATE_BM 0x70
#define CCxx00_FIFO_BYTES_AVAILABLE_BM 0x0F
#define CCxx00_STATE_TX_BM 0x20
#define CCxx00_STATE_TX_UNDERFLOW_BM 0x70
#define CCxx00_STATE_RX_BM 0x10
#define CCxx00_STATE_RX_OVERFLOW_BM 0x60
#define CCxx00_STATE_IDLE_BM 0x00
static INT8U RfGetRxStatus(void)
{
INT8U temp, spiRxStatus1,spiRxStatus2;
INT8U i=4;// 循環測試次數
temp = CCxxx0_SNOP|READ_SINGLE;//讀寄存器命令
CSN = 0;
while (MISO);
SpiTxRxByte(temp);
spiRxStatus1 = SpiTxRxByte(0);
do
{
SpiTxRxByte(temp);
spiRxStatus2 = SpiTxRxByte(0);
if(spiRxStatus1 == spiRxStatus2)
{
if( (spiRxStatus1 & CCxx00_STATE_BM) == CCxx00_STATE_RX_OVERFLOW_BM)
{
halSpiStrobe(CCxxx0_SFRX);
return 0;
}
return 1;
}
spiRxStatus1=spiRxStatus2;
}
while(i--);
CSN = 1;
return 0;
}
*/
INT8U halRfReceivePacket(INT8U *rxBuffer, INT8U *length)
{
INT8U status[2];
INT8U packetLength;
INT8U i=(*length)*4; // 具體多少要根據datarate和length來決定
halSpiStrobe(CCxxx0_SRX); //進入接收狀態
//delay(5);
//while (!GDO1);
//while (GDO1);
delay(2);
while (GDO0)
{
delay(2);
--i;
if(i<1)
return 0;
}
if ((halSpiReadStatus(CCxxx0_RXBYTES) & BYTES_IN_RXFIFO)) //如果接的字節數不為0
{
packetLength = halSpiReadReg(CCxxx0_RXFIFO);//讀出第一個字節，此字節為該幀數據長度
if (packetLength <= *length) //如果所要的有效數據長度小于等于接收到的數據包的長度
{
halSpiReadBurstReg(CCxxx0_RXFIFO, rxBuffer, packetLength); //讀出所有接收到的數據
*length = packetLength; //把接收數據長度的修改為當前數據的長度
// Read the 2 appended status bytes (status[0] = RSSI, status[1] = LQI)
halSpiReadBurstReg(CCxxx0_RXFIFO, status, 2); //讀出CRC校驗位
halSpiStrobe(CCxxx0_SFRX); //清洗接收緩沖區
return (status[1] & CRC_OK); //如果校驗成功返回接收成功
}
else
{
*length = packetLength;
halSpiStrobe(CCxxx0_SFRX); //清洗接收緩沖區
return 0;
}
}
else
return 0;
}
/*
void Delay(unsigned int s)
{
unsigned int i;
for(i=0; i<s; i++);
for(i=0; i<s; i++);
}
*/
//uchar key_scan()
//{
// //上升、下降
// if((KEY1==0)) //第一次 key_up=1 此時如果有操作按鍵按下則執行下面的程序||key3==0key_up&&
// {
// delay1ms(10); //延時小豆
// if((KEY1==0)) //||key3==0key_up&&
// {
//// key_up=0; //松手標志位0 那么下次檢測, if 結果就為0 則就不會執行這里的語句
////
//// key_down=1; //按鍵被按下標志最后如果按鍵松手，那么還應該發送一個數據出去執行關閉
//
//// if(KEY1==0) //
// return 1;
//// if(key3==0)
//// return 3;
// }
// }
// else
//// if(KEY1!=0) //上升下降按鍵都沒有被按下&&key3==1
// {
//// key_up=1; //必須所有按鍵都沒有被按下松手標志初始化
//// if(key_down==1) //這里判斷按鍵是否按下過，按下過就發送一個數據過去關閉之前的輸出
//// {
//// key_down=0; //初始化
// return 99; //返回值
//// }
// }
//
//}
void main(void)
{
// P2M1=0x0f;
// P2M0=0x00;
INT8U leng =8,i=0,mode=0,cont=0,offset=0,flag1=0,key_num,tf1=0,key_down1=0,key_down=0;
INT8U tf =0;
// INT8U DS_UP=0;DS_STOP=0;DS_DOWN=0;
INT8U TxBuf[8]={0}; // 8字節, 如果需要更長的數據包,請正確設置
INT8U RxBuf[8]={0};
INT8U code *cptr;
INT8U idata *iptr;
cptr=ID_ADDR_ROM;
iptr=ID_ADDR_RAM;
for(i=0;i<7;i++)
id[i]=cptr[i];
//id[6]=3;
P1M1=0x00;
P1M0=0x01;
//P2M1=0x40;
//P2M0=0x40;
CpuInit();
POWER_UP_RESET_CC1100();
halRfWriteRfSettings();
halSpiWriteBurstReg(CCxxx0_PATABLE, PaTabel, 8);
TxBuf[1]=1;TxBuf[2]=0;led1=1;//;led5=0
//halRfSendPacket(TxBuf,8); // Transmit Tx buffer data
INT1=1;
IT1=1;
EX1=1; //開啟外部中斷1
EA=1;
TL1 = BAUD;
TH1 = BAUD >> 8;
TR1 = 1;
ET1 = 1;
PT1 = 1;
// EX0=1; //開啟外部中斷0
TMOD=0x01; //T0方式為1 16位
TH0=(65536-50000)/256;
TL0=(65536-50000)%256; //50000*12*(1/12M)=50ms
TR0=1; //啟動定時器T0
ET0=1; //使能定時器T0中斷
// key_up=0;
delay1s(3);
// P2M1=0x0f;
// P2M0=0x00;
if(KEY0==0)
{
delay1ms(10);
if(KEY0==0)
mode=1;//學習模式
led1=0;//亮
delay1ms(10);
led1=1;//亮
}
offset=0;
TxBuf[offset++]=0xaa;//普通數據
TxBuf[offset++]=0xbb;
TxBuf[offset++]=id[3];
TxBuf[offset++]=id[4];
TxBuf[offset++]=id[5];
TxBuf[offset++]=id[6];
//輸入模式
// P2M0 = 0x00;
// P2M1 = 0x0F;
while(1)
{
//接收端
/*if(halRfReceivePacket(RxBuf,&leng))
{
}*/
//發送端
if(mode==1)
{//
if((KEY0==0)&&(KEY3==0))
{
delay1ms(10);
if((KEY0==0)&&(KEY3==0))
{
if(cont<4)
{
cont++;
}
}
// while((KEY0==0)&&(KEY3==0));
}
if(cont==4)
{
led1=0;//亮
offset=0;
TxBuf[offset++]=0xff;//識別碼標志
TxBuf[offset++]=0xff;
TxBuf[offset++]=id[3];
TxBuf[offset++]=id[4];
TxBuf[offset++]=id[5];
TxBuf[offset++]=id[6];
halRfSendPacket(TxBuf,8);
delay1ms(200);
led1=1;//熄滅
delay1ms(200);
// mode=0;
}
}
else
{//正常模式發送按鍵數據
// if(key_up&&KEY1==0)//第一次key_up==1;那么如果其他按鍵有按下，則為真，執行下面程序
if(((KEY1==1)&&(KEY3==1))&&(KEY2!=0))//點動上升
{
delay1ms(50);
if(((KEY1==1)&&(KEY3==1))&&(KEY2!=0))
{
TxBuf[1]=0xa1;
tf1=1;
key_down=0;
key_down1=0;
ET0=1;
}
}
else if((KEY1==0)&&(key_down1==0))
{
delay1ms(50);
if(KEY1==0)
{
TxBuf[1]=0xb1;
tf1=1;
key_down=1;
ET0=0;
led2=0;//亮
delay1ms(30);
led2=1;//亮
}
}
// if(KEY3==1)//點動下降
// {
// delay1ms(50);
// if(KEY3==1)
// {
// TxBuf[1]=0xa2;
// tf1=1;
// key_down1=0;
// }
// }
else if((KEY3==0)&&(key_down==0))
{
delay1ms(50);
if(KEY3==0)
{
TxBuf[1]=0xb2;
tf1=1;
key_down1=1;
ET0=0;
led2=0;//亮
delay1ms(30);
led2=1;//亮
}
}
if(KEY0==0)//停止
{
delay1ms(50);
if(KEY0==0)
{
TxBuf[1]=0xcc;
tf1=1;
ET0=1;
led2=0;//亮
delay1ms(30);
led2=1;//亮
}
}
if(KEY2==0)//啟動
{
delay1ms(50);
if(KEY2==0)
{
TxBuf[1]=0xc5;
tf1=1;
ET0=1;
led2=0;//亮
delay1ms(30);
led2=1;//亮
}
}
if (tf1==1)
{
TxBuf[HEAD_LEN]=2;
halRfSendPacket(TxBuf,8);
tf1=0;
}
}
if(num>=80)
{
halSpiStrobe(CCxxx0_SIDLE); //進入空閑模式
halSpiStrobe(CCxxx0_SXOFF);
halSpiStrobe(CCxxx0_SPWD); //關閉無線模塊
_nop_();
_nop_();
_nop_();
num=0;
// led2=0;
ET0=0;
delay(500);
// led1=0;
PCON=0X02; //PD=1,進入掉電模式 //PCON=0X01;//IDL=1,進入空閑模式
_nop_();
_nop_();
_nop_();
}
}
}
void exint1() interrupt 2
{
PCON=0;
// led1=1;
}
void timer0() interrupt 1
{
TH0=(65536-50000)/256;
TL0=(65536-50000)%256; //50000*12*(1/12M)=50ms
num++;//每50ms加1
}