stc15w408as和rfid-rc522如何進行刷卡求思路

ID:708209 · 發表于 2020-4-5 17:37

各位大佬最近在做個刷卡功能的單片機，用的時stc15w408as，然后根據rc-522給的51單片機代碼，改了下管腳定義，但是在上位機上卻尋不到卡，有沒有大佬能幫我看下怎么改才能正常工作

ID:708209 · 發表于 2020-4-5 17:38

這是我的代碼
#include "reg52.h"
#include "main.h"
#include "mfrc522.h"
#include <string.h>
//M1卡的某一塊寫為如下格式，則該塊為錢包，可接收扣款和充值命令
//4字節金額（低字節在前）＋4字節金額取反＋4字節金額＋1字節塊地址＋1字節塊地址取反＋1字節塊地址＋1字節塊地址取反
unsigned char code data2[4]  = {0x12,0,0,0};
unsigned char code DefaultKey[6] = {0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF};
unsigned char g_ucTempbuf[20];
unsigned char idata MLastSelectedSnr[4];
unsigned char idata RevBuffer[30];
unsigned char data SerBuffer[20];
bit CmdValid;

void iccardcode()
{
    unsigned char cmd;
unsigned char status;

cmd = RevBuffer[0];
switch(cmd)
{
case 1:    // Halt the card    //終止卡的操作
status= PcdHalt();;
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
case 2:    // Request,Anticoll,Select,return CardType(2 bytes)+CardSerialNo(4 bytes)
         // 尋卡，防沖突，選擇卡返回卡類型（2 bytes）+ 卡系列號(4 bytes)
status= PcdRequest(RevBuffer[1],&RevBuffer[2]);
if(status!=0)
{
status= PcdRequest(RevBuffer[1],&RevBuffer[2]);
if(status!=0)
{
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
}
}
RevBuffer[0]=3;
RevBuffer[1]=status;
break;

case 3:                      // 防沖突讀卡的系列號 MLastSelectedSnr
status = PcdAnticoll(&RevBuffer[2]);
if(status!=0)
{
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
}
memcpy(MLastSelectedSnr,&RevBuffer[2],4);
RevBuffer[0]=5;
RevBuffer[1]=status;
break;
case 4:                      // 選擇卡 Select Card
status=PcdSelect(MLastSelectedSnr);
if(status!=MI_OK)
{
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
}
RevBuffer[0]=3;
RevBuffer[1]=status;
break;
case 5:       // Key loading into the MF RC500's EEPROM
         status = PcdAuthState(RevBuffer[1], RevBuffer[3], DefaultKey, MLastSelectedSnr);// 校驗卡密碼
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
case 6:
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
case 7:
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
case 8:    // Read the mifare card
            // 讀卡
status=PcdRead(RevBuffer[1],&RevBuffer[2]);
if(status==0)
{RevBuffer[0]=17;}
else
{RevBuffer[0]=1;}
RevBuffer[1]=status;
break;
case 9:    // Write the mifare card
            // 寫卡  下載密碼
status=PcdWrite(RevBuffer[1],&RevBuffer[2]);
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
case 10:
         PcdValue(RevBuffer[1],RevBuffer[2],&RevBuffer[3]);
RevBuffer[0]=1;
RevBuffer[1]=status;
break;
case 12: // 參數設置
      PcdBakValue(RevBuffer[1], RevBuffer[2]);
RevBuffer[0]=1; //contact
RevBuffer[1]=0;
break;
}

}
/////////////////////////////////////////////////////////////////////
//系統初始化
/////////////////////////////////////////////////////////////////////
void InitializeSystem()
{
P0 = 0xFF; P1 = 0xFF; P3 = 0xFF;

ET2 = 0;
T2CON = 0x04;
PCON = 0x80;
SCON = 0x70;
TMOD = 0x21;       //TMOD = 0x22;

TH1 = BAUD_9600;
TL1 = TH1;
TR1 = 1;          // 波特率發生器

TH0 = 0x60;
TL0 = 0x60;
TR0 = 0;

ET0=0;
ET1=0;
EA=1;
EX0=1;
IT0 = 1;
TR2=0;
ES = 1;
CmdValid=0;

   LED_GREEN = 1;
   PcdReset();
   PcdAntennaOff();
   PcdAntennaOn();
   M500PcdConfigISOType( 'A' );
   LED_GREEN = 0;
   delay_10ms(10);
   LED_GREEN = 1;
   delay_10ms(10);
   LED_GREEN = 0;
}

/////////////////////////////////////////////////////////////////////
//用T2做延時子程序
/////////////////////////////////////////////////////////////////////

///////////////////////////////////////////////////////////////////////
// 接收和發送中斷
///////////////////////////////////////////////////////////////////////
void isr_UART(void) interrupt 4 using 1
{
unsigned char len, i;
    unsigned int j=0;

    if(RI)
{
len=SBUF;
RI=0;
for(i=0;i<len;i++)
{
while(!RI)
{
j++;
if(j>1000)
{
      break;
}
}
if(j<1000)
{
RevBuffer[i]=SBUF;
RI=0;
j=0;
}
else
{
      break;
}
}
if(i==len)
{
REN=0;
CmdValid=1;
}
}
else if(!RI && TI)
{
TI=0;
len=RevBuffer[0];
for(i=0;i<len+1;i++)
{
SBUF=RevBuffer[i];
while(!TI);
TI=0;
}
REN=1;
}
}

  void main( )
{
unsigned char baud;
   InitializeSystem( );
while (1)
{
      if (CmdValid)
      {
      CmdValid = FALSE;
      if(RevBuffer[0]==11)       //為了加快相應速度測試風鳴器
      {
        RevBuffer[2]=RevBuffer[1];
              RevBuffer[0]=1;       //contact
        RevBuffer[1]=0;
        CALL_isr_UART();
            LED_GREEN = 1;
        delay_10ms(RevBuffer[2]);
            LED_GREEN = 0;
      }
        else if(RevBuffer[0]==13) //設置通訊波特率
        {
switch(RevBuffer[1])
{
case 0:
        baud=BAUD_9600;
        break;
        case 1:
        baud=BAUD_14400;
        break;
        case 2:
        baud=BAUD_19200;
        break;
        case 3:
        baud=BAUD_28800;
        break;
        case 4:
        baud=BAUD_38400;
        break;
        case 5:
        baud=BAUD_57600;
        break;
        case 6:
        baud=BAUD_115200;
        break;
        default:
        baud=BAUD_9600;
        break;
        }
        RevBuffer[0]=1;          //contact
        RevBuffer[1]=0;
        CALL_isr_UART();
        delay_10ms(5);
        TR1 = 0;
        TH1 = baud;
        TL1 = TH1;
        delay_10ms(2);
        TR1 = TRUE;
        }

   else
{
            iccardcode();
CALL_isr_UART();
}

   }
   }
}

ID:708209 · 發表于 2020-4-5 17:38

本帖最后由陳慢慢于 2020-4-5 17:49 編輯

/*  BYTE Registers  */
sfr P0 = 0x80;
sfr P1 = 0x90;
sfr P2 = 0xA0;
sfr P3 = 0xB0;
sfr PSW = 0xD0;
sfr ACC = 0xE0;
sfr B    = 0xF0;
sfr SP = 0x81;
sfr DPL = 0x82;
sfr DPH = 0x83;
sfr PCON  = 0x87;
sfr TCON  = 0x88;
sfr TMOD  = 0x89;
sfr TL0 = 0x8A;
sfr TL1 = 0x8B;
sfr TH0 = 0x8C;
sfr TH1 = 0x8D;
sfr IE = 0xA8;
sfr IP = 0xB8;
sfr SCON  = 0x98;
sfr SBUF  = 0x99;

/*  8052 Extensions  */
sfr T2CON  = 0xC8;
sfr RCAP2L = 0xCA;
sfr RCAP2H = 0xCB;
sfr TL2 = 0xCC;
sfr TH2 = 0xCD;

/*  BIT Registers  */
/*  PSW  */
sbit CY = PSW^7;
sbit AC = PSW^6;
sbit F0 = PSW^5;
sbit RS1 = PSW^4;
sbit RS0 = PSW^3;
sbit OV = PSW^2;
sbit P    = PSW^0; //8052 only

/*  TCON  */
sbit TF1 = TCON^7;
sbit TR1 = TCON^6;
sbit TF0 = TCON^5;
sbit TR0 = TCON^4;
sbit IE1 = TCON^3;
sbit IT1 = TCON^2;
sbit IE0 = TCON^1;
sbit IT0 = TCON^0;

/*  IE  */
sbit EA = IE^7;
sbit ET2 = IE^5; //8052 only
sbit ES = IE^4;
sbit ET1 = IE^3;
sbit EX1 = IE^2;
sbit ET0 = IE^1;
sbit EX0 = IE^0;

/*  IP  */
sbit PT2 = IP^5;
sbit PS = IP^4;
sbit PT1 = IP^3;
sbit PX1 = IP^2;
sbit PT0 = IP^1;
sbit PX0 = IP^0;

/*  P3  */
sbit RD = P3^7;
sbit WR = P3^6;
sbit T1 = P3^5;
sbit T0 = P3^4;
sbit INT1  = P3^3;
sbit INT0  = P3^2;
sbit TXD = P3^1;
sbit RXD = P3^0;

sfr P5 = 0xC8;
sbit P54  = P5^4;
sbit P55  = P5^5;

/*  SCON  */
sbit SM0 = SCON^7;
sbit SM1 = SCON^6;
sbit SM2 = SCON^5;
sbit REN = SCON^4;
sbit TB8 = SCON^3;
sbit RB8 = SCON^2;
sbit TI = SCON^1;
sbit RI = SCON^0;

/*  P1  */
sbit T2EX    = P1^1; // 8052 only
sbit T2       = P1^0; // 8052 only

/*  T2CON  */
sbit TF2       = T2CON^7;
sbit EXF2    = T2CON^6;
sbit RCLK    = T2CON^5;
sbit TCLK    = T2CON^4;
sbit EXEN2    = T2CON^3;
sbit TR2       = T2CON^2;
sbit C_T2    = T2CON^1;
sbit CP_RL2    = T2CON^0;

//sbit SPEAKER = P1^6;
//sbit RC500RST = P3^3;

sfr16 RCAP2LH = 0xCA;
sfr16 T2LH = 0xCC;

ID:708209 · 發表于 2020-4-5 17:39

//////////////////////////////////
//端口定義
/////////////////////////////////////////////////////////////////////
//MFRC522
sbit    MF522_RST  = P5^4;                //RC500片選
sbit    MF522_NSS  = P1^2;
sbit    MF522_SCK  = P1^5;
sbit    MF522_SI = P1^3;
sbit    MF522_SO = P1^4;
//指示燈
//指示燈
sbit    LED_GREEN  = P1^5;
/////////////////////////////////////////////////////////////////////
//函數原型
/////////////////////////////////////////////////////////////////////
void InitializeSystem();
#define BAUD_115200          256 - (OSC_FREQ/192L)/115200L // 255
#define BAUD_57600             256 - (OSC_FREQ/192L)/57600L // 254
#define BAUD_38400             256 - (OSC_FREQ/192L)/38400L // 253
#define BAUD_28800             256 - (OSC_FREQ/192L)/28800L // 252
#define BAUD_19200             256 - (OSC_FREQ/192L)/19200L // 250
#define BAUD_14400             256 - (OSC_FREQ/192L)/14400L // 248
#define BAUD_9600             256 - (OSC_FREQ/192L)/9600L    // 244
#define OSC_FREQ             22118400L
//#define  OSC_FREQ       7372800L
#define OSC_FREQ       22118400L
#define  RCAP2_50us    65536L - OSC_FREQ/40417L
#define  RCAP2_1ms    65536L - OSC_FREQ/2000L
#define  RCAP2_10ms    65536L - OSC_FREQ/1200L
#define  TIME0_500us    65536L - OSC_FREQ/8000L
#define  TIME0_10ms    65536L - OSC_FREQ/200

#define CALL_isr_UART()       TI = 1
#define TRUE 1
#define FALSE 0

ID:338503 · 發表于 2024-12-28 17:06

stc15w408as單片機的IO需要先設置工作模式，就是PxM0和PxM1要作相應設置才可以。

ID:338503 · 發表于 2024-12-30 07:31

ID:338503 · 發表于 2024-12-30 07:44

例如可以這樣設置：P1M0 = 0x2C; P1M1=0x10; // P1.2 P1.3 P1.5為推挽輸出模式 P1.4為高阻輸入

P5M0 |= 0x10; P5M1 &= ~0x10; /0001 0000設置P5.4 為推挽輸出模式

帳號		自動登錄	找回密碼
密碼			立即注冊

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

stc15w408as和rfid-rc522如何進行刷卡 求思路

stc15w408as和rfid-rc522如何進行刷卡求思路