野火stm32f4讀寫內部flash程序按字，按半字，按字節

ID:484359 · 發表于 2019-10-4 15:55

參考野火給的程序移植而成，需要的可以下載來使用，代碼已經調試好，打開串口助手查看結果

單片機源程序如下:

#include "stm32f4xx.h"
#include "./usart/bsp_debug_usart.h"
#include "./led/bsp_led.h"
#include "./internalFlash/bsp_internalFlash.h"
void delay(unsigned int x)
{
while(x--);
}
/**
* @brief 主函數
* @param 無
* @retval 無
*/
int main(void)
{
unsigned int m;
uint32_t aa[2] = {0x12345678,0x11111111};
uint32_t bb[2] = {0};
uint16_t aa1[5] = {400,500,600,700,800};
uint16_t bb1[5] = {0};
uint8_t aa2[10] = {0,1,2,3,4,5,6,7,8,9};
uint8_t bb2[10] = {0};
/*初始化USART，配置模式為 115200 8-N-1*/
Debug_USART_Config();
LED_GPIO_Config();
LED_BLUE;
/*調用printf函數，因為重定向了fputc，printf的內容會輸出到串口*/
printf("正在進行讀寫內部FLASH實驗,請耐心等待 \r\n");
printf("開始寫入32位數據\r\n：");
if(Write_Wordbyte(ADDR_FLASH_SECTOR_8,ADDR_FLASH_SECTOR_9,aa,2) == 1)
{
LED_GREEN;
}
for(m = 0;m < 2;m++)
{
printf("寫入的32位數據為 = %X\r\n",aa[m]);
delay(0xfffff);
}
if(Read_Wordbyte(ADDR_FLASH_SECTOR_8,2,bb) == 1)
{
LED_RED;
}
for(m = 0;m < 2;m++)
{
printf("讀出的32位數據為 = %X\r\n",bb[m]);
delay(0xfffff);
}
////////////////////////////////////////
printf("開始寫入16位數據r\n");
if(Write_HalfWordbyte(ADDR_FLASH_SECTOR_8,ADDR_FLASH_SECTOR_9,aa1,5) == 1)
{
LED_GREEN;
}
for(m = 0;m < 5;m++)
{
printf("寫入的16位數據為 = %d\r\n",aa1[m]);
delay(0xfffff);
}
if(Read_HalfWordbyte(ADDR_FLASH_SECTOR_8,5,bb1) == 1)
{
LED_RED;
}
for(m = 0;m < 5;m++)
{
printf("讀出的16位數據為 = %d\r\n",bb1[m]);
delay(0xfffff);
}
///////////////////////////////////
printf("開始寫入8位數據\r\n");
if(Write_Byte(ADDR_FLASH_SECTOR_8,ADDR_FLASH_SECTOR_9,aa2,10) == 1)
{
LED_GREEN;
}
for(m = 0;m < 10;m++)
{
printf("寫入的8位數據為 = %d\r\n",aa2[m]);
delay(0xfffff);
}
if(Read_Byte(ADDR_FLASH_SECTOR_8,10,bb2) == 1)
{
LED_RED;
}
for(m = 0;m < 10;m++)
{
printf("讀出的8位數據為 = %d\r\n",bb2[m]);
delay(0xfffff);
}
while(1)
{ }
}
/*********************************************END OF FILE**********************/