STC5A60S2+nrf24l01芯片代碼

ID:485556 · 發表于 2019-3-14 20:46

前幾日從某寶平臺購得一nrf24l01據悉為臺產芯片
使用單片機為STC5A60S2
代碼如下，僅供參考

#include "STC5A60S2.H"
#include <intrins.h>
#include <string.h>
#include "NRF_24L01.h"
#include "UART.H"
#define uchar unsigned char
uchar const TX_ADDRESS[TX_ADR_WIDTH] = {0x34,0x43,0x10,0x10,0x01}; // Define a static TX address
uchar rx_buf[TX_PLOAD_WIDTH];
uchar tx_buf[TX_PLOAD_WIDTH];
uchar flag;
/**************************************************/
//sbit LED1= P3^7;
/**************************************************/
unsigned char bdata sta;
sbit RX_DR =sta^6;
sbit TX_DS =sta^5;
sbit MAX_RT =sta^4;
/**************************************************/
/**************************************************
Function: init_io();
Description:
flash led one time,chip enable(ready to TX or RX Mode),
Spi disable,Spi clock line init high
/**************************************************/
#define KEY 0xaa
void init_nrf24l01_io(void)
{
CE=0; // chip enable
CSN=1; // Spi disable
SCK=0; // Spi clock line init high
}
/**************************************************/
/**************************************************
Function: Inituart();
Description:
set uart working mode
/**************************************************/
void delay_ms(unsigned int _ms)
{
for(_ms;_ms;_ms--)
{
_delay_us(1000);
}
}
/**************************************************/
/**************************************************
Function: SPI_RW();
Description:
Writes one byte to nRF24L01, and return the byte read
from nRF24L01 during write, according to SPI protocol
/**************************************************/
bdata unsigned char st=0;
sbit st_1=st^0;
sbit st_2=st^1;
sbit st_3=st^2;
sbit st_4=st^3;
sbit st_5=st^4;
sbit st_6=st^5;
sbit st_7=st^6;
sbit st_8=st^7;
bdata unsigned char st1=0;
sbit st_11=st1^0;
sbit st_12=st1^1;
sbit st_13=st1^2;
sbit st_14=st1^3;
sbit st_15=st1^4;
sbit st_16=st1^5;
sbit st_17=st1^6;
sbit st_18=st1^7;
/*
uchar SPI_RW(uchar byte)
{
uchar bit_ctr;
for(bit_ctr=0;bit_ctr<8;bit_ctr++) // output 8-bit
{
MOSI = (byte & 0x80); // output 'byte', MSB to MOSI
byte = (byte << 1); // shift next bit into MSB..
SCK = 1; // Set SCK high..
MISO=1;
byte |= MISO; // capture current MISO bit
SCK = 0; // ..then set SCK low again
}
return(byte); // return read byte
}
*/
uchar SPI_RW(uchar byte)
{
//uchar bit_ctr;
st=byte;
MOSI=st_8;
SCK = 1;
st_18=MISO;
SCK = 0;
MOSI=st_7;
SCK = 1;
st_17=MISO;
SCK = 0;
MOSI=st_6;
SCK = 1;
st_16=MISO;
SCK = 0;
MOSI=st_5;
SCK = 1;
st_15=MISO;
SCK = 0;
MOSI=st_4;
SCK = 1;
st_14=MISO;
SCK = 0;
MOSI=st_3;
SCK = 1;
st_13=MISO;
SCK = 0;
MOSI=st_2;
SCK = 1;
st_12=MISO;
SCK = 0;
MOSI=st_1;
SCK = 1;
st_11=MISO;
SCK = 0;
return(st1); // return read byte
}
/**************************************************/
/**************************************************
Function: SPI_RW_Reg();
Description:
Writes value 'value' to register 'reg'
/**************************************************/
uchar SPI_RW_Reg(BYTE reg, BYTE value)
{
uchar status;
CSN = 0; // CSN low, init SPI transaction
status = SPI_RW(reg); // select register
SPI_RW(value); // ..and write value to it..
CSN = 1; // CSN high again
return(status); // return nRF24L01 status byte
}
/**************************************************/
/**************************************************
Function: SPI_Read();
Description:
Read one byte from nRF24L01 register, 'reg'
/**************************************************/
BYTE SPI_Read(BYTE reg)
{
BYTE reg_val;
CSN = 0; // CSN low, initialize SPI communication...
SPI_RW(reg); // Select register to read from..
reg_val = SPI_RW(0); // ..then read registervalue
CSN = 1; // CSN high, terminate SPI communication
return(reg_val); // return register value
}
/**************************************************/
/**************************************************
Function: SPI_Read_Buf();
Description:
Reads 'bytes' #of bytes from register 'reg'
Typically used to read RX payload, Rx/Tx address
/**************************************************/
uchar SPI_Read_Buf(BYTE reg, BYTE *pBuf, BYTE bytes)
{
uchar status,byte_ctr;
CSN = 0; // Set CSN low, init SPI tranaction
status = SPI_RW(reg); // Select register to write to and read status byte
for(byte_ctr=0;byte_ctr<bytes;byte_ctr++)
pBuf[byte_ctr] = SPI_RW(0); // Perform SPI_RW to read byte from nRF24L01
CSN = 1; // Set CSN high again
return(status); // return nRF24L01 status byte
}
/**************************************************/
/**************************************************
Function: SPI_Write_Buf();
Description:
Writes contents of buffer '*pBuf' to nRF24L01
Typically used to write TX payload, Rx/Tx address
/**************************************************/
uchar SPI_Write_Buf(BYTE reg, BYTE *pBuf, BYTE bytes)
{
uchar status,byte_ctr;
CSN = 0; // Set CSN low, init SPI tranaction
status = SPI_RW(reg); // Select register to write to and read status byte
for(byte_ctr=0; byte_ctr<bytes; byte_ctr++) // then write all byte in buffer(*pBuf)
SPI_RW(*pBuf++);
CSN = 1; // Set CSN high again
return(status); // return nRF24L01 status byte
}
/**************************************************/
/**************************************************
Function: RX_Mode();
Description:
This function initializes one nRF24L01 device to
RX Mode, set RX address, writes RX payload width,
select RF channel, datarate & LNA HCURR.
After init, CE is toggled high, which means that
this device is now ready to receive a datapacket.
/**************************************************/
void power_off()
{
CE=0;
SPI_RW_Reg(WRITE_REG + CONFIG, 0x0D);
CE=1;
_delay_us(20);
}
void ifnnrf_rx_mode(void)
{
power_off();
CE=0;
SPI_Write_Buf(WRITE_REG + RX_ADDR_P0, TX_ADDRESS, TX_ADR_WIDTH); // Use the same address on the RX device as the TX device
SPI_RW_Reg(WRITE_REG + EN_AA, 0x01); // Enable Auto.Ack:Pipe0
SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01); // Enable Pipe0
SPI_RW_Reg(WRITE_REG + RF_CH, 40); // Select RF channel 40
SPI_RW_Reg(WRITE_REG + RX_PW_P0, TX_PLOAD_WIDTH); // Select same RX payload width as TX Payload width
SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x07); // TX_PWR:0dBm, Datarate:2Mbps, LNA:HCURR
SPI_RW_Reg(WRITE_REG + CONFIG, 0x0f); // Set PWR_UP bit, enable CRC(2 bytes) & Prim:RX. RX_DR enabled..
CE = 1; // Set CE pin high to enable RX device
// This device is now ready to receive one packet of 16 bytes payload from a TX device sending to address
// '3443101001', with auto acknowledgment, retransmit count of 10, RF channel 40 and datarate = 2Mbps.
}
/**************************************************/
/**************************************************
Function: TX_Mode();
Description:
This function initializes one nRF24L01 device to
TX mode, set TX address, set RX address for auto.ack,
fill TX payload, select RF channel, datarate & TX pwr.
PWR_UP is set, CRC(2 bytes) is enabled, & PRIM:TX.
ToDo: One high pulse(>10us) on CE will now send this
packet and expext an acknowledgment from the RX device.
/**************************************************/
void ifnnrf_tx_mode(void)
{
power_off();
CE=0;
SPI_Write_Buf(WRITE_REG + TX_ADDR, TX_ADDRESS, TX_ADR_WIDTH); // Writes TX_Address to nRF24L01
SPI_Write_Buf(WRITE_REG + RX_ADDR_P0, TX_ADDRESS, TX_ADR_WIDTH); // RX_Addr0 same as TX_Adr for Auto.Ack
SPI_Write_Buf(WR_TX_PLOAD, tx_buf, TX_PLOAD_WIDTH); // Writes data to TX payload
SPI_RW_Reg(WRITE_REG + EN_AA, 0x01); // Enable Auto.Ack:Pipe0
SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01); // Enable Pipe0
SPI_RW_Reg(WRITE_REG + SETUP_RETR, 0x1a); // 500us + 86us, 10 retrans...
SPI_RW_Reg(WRITE_REG + RF_CH, 40); // Select RF channel 40
SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x07); // TX_PWR:0dBm, Datarate:2Mbps, LNA:HCURR
SPI_RW_Reg(WRITE_REG + CONFIG, 0x0e); // Set PWR_UP bit, enable CRC(2 bytes) & Prim:TX. MAX_RT & TX_DS enabled..
CE=1;
}
void SPI_CLR_Reg(BYTE R_T)
{
CSN = 0;
if(R_T==1) // CSN low, init SPI transaction
SPI_RW(FLUSH_TX); // ..and write value to it..
else
SPI_RW(FLUSH_RX); // ..and write value to it..
CSN = 1; // CSN high again
}
void ifnnrf_CLERN_ALL()
{
SPI_CLR_Reg(0);
SPI_CLR_Reg(1);
SPI_RW_Reg(WRITE_REG+STATUS,0xff);
IRQ=1;
}

復制代碼

帳號		自動登錄	找回密碼
密碼			立即注冊

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

STC5A60S2+nrf24l01芯片代碼

評分