RDA5856代碼開發手冊 IOT藍牙雙模芯片源碼與資料下載

ID:402760 · 發表于 2018-9-26 17:15

紫光展銳旗下銳迪科微電子的藍牙雙模單芯片方案 RDA5856，該方案具有強大的音頻處理和藍牙連接功能，為藍牙音響、車載終端、智能家居等消費電子市場提供普及型的物聯網解決方案。

RDA5856 實現了藍牙雙模的 SOC，在單芯片上集成高性能 MCU、Bluetooth、FM Radio、PMU、Codec 及 Memory，支持V2.1（2.1+EDR）和 BLE 兩種模式，并擁有豐富的接口資源，滿足各類藍牙產品的開發需求。

RDA5856 采用自主研發的降噪算法和回聲抑制算法，藍牙音樂播放的信噪比可以達到 -90dB 以上，同時該芯片具有優秀的射頻靈敏度，BR 靈敏度達到 -94dBm 以上。RDA5856 具備強大的抗干擾和穿墻能力以及更持久的續航能力，適用于各種藍牙音箱，頭戴式耳機、聲霸等多種應用場合。

RDA5856 已通過嚴格的藍牙標準認證，取得了藍牙 V4.2 的 QDID 證書。RDA 根據應用領域的不同推出了 TSSOP、LQFP、QFN 等多種封裝形式，最大程度滿足客戶差異化需求。

5856_codec 注意事項：

燒寫口
因為默認的debug口（P44，P45）和SD卡的clk和cmd線復用，所以如果要使用sd卡，就得通過板上的撥碼開關來把默認的debug口換成P41，P42，原來debug口的pinmux改成function5.
Pinmux的配置可以在tgt_board_cfg.h中更改。

當不使用SD卡時，就可以把P44，P45的pinmux設成0.（默認的代碼就是0）。撥碼開關兩個都撥到上端。
當使用SD卡時，就可以把P44，P45的pinmux設成5. 然后燒寫時先把撥碼開關撥到上端（只是延時了3s，所以按完reset鍵就得馬上燒寫），燒寫成功后再把撥碼開關都撥到下端。
另外因為芯片內部spi不通，所以需通過5855e板的I2C來設置5956板的pmu （5855e的I2C需用導線連接到5856的I2C2上）。

程序源碼：

/********************************************************************************
* RDA API FOR MP3HOST
*
* (c) Copyright, RDA Co,Ld.
* All Right Reserved
*
********************************************************************************/
#include "ap_common.h"
#include "ap_calendar.h"
#include "ap_idle.h"
#include "ap_linein.h"
#include "ap_record.h"
#include "ap_setting.h"
#include "ap_fm.h"
#include "ap_music.h"
#include "ap_bluetooth.h"
#include "ap_usbdisk.h"
#include "ap_charging.h"
#include "tm.h"
#include "MainTask.h"
#include "event.h"
#include "gpio_edrv.h"
#define READ_BUF_MAX 128
#define MAIN_ITEMCOUNT 5 /*Main Menu Nums*/
#define MAX_BOOT_LOGO_PICS 6 /*BootLogo Nums Used by User*/
#define UPDATE_TFLASH_BIN_NAME L"tflash_update.bin"
static const UINT16 boot_logo_pic[MAX_BOOT_LOGO_PICS] = {GUI_IMG_LOGO, GUI_IMG_LOGO, GUI_IMG_LOGO, GUI_IMG_LOGO, GUI_IMG_LOGO, GUI_IMG_LOGO};
///////////////////////////////////////////////////////////////////////////////////
comval_t *g_comval; //系統總的環境變量
slider_t slider = {0};
//function_menu_t menu;
//progress_t progress;
sysconfig_t g_sysconfig = {0};
displayconfig_t g_displayconfig = {0};
#if APP_SUPPORT_BLUETOOTH==1
btconfig_t g_btconfig = {0};
#endif
INT32 g_last_reslt = -1;
INT32 g_current_module = 0;
//////////////////////////////////////////////////////////////////////////////////
//add by wuxiang
extern UINT16 call_status;
extern UINT32 g_bt_call_time;
//add end
extern BOOL ui_auto_update;
extern BOOL ui_auto_select;
extern BOOL g_test_mode;
extern UINT8 g_usb_active_after_bt;
UINT32 event_detected_displaying_log;
extern UINT8 g_linein_out_event;
extern UINT8 g_usb_audio_linein;
extern UINT8 g_usb_audio_tcard;
#if APP_SUPPORT_FADE_INOUT==1
extern INT8 g_fade_volume_backup;
#endif
extern UINT32 musicplay_timer;
void APP_Test_Mode(void);
typedef INT32 (*MOD_FunCbPtr )(INT32 param);
/* Mod Functions To Entry Every Mod By Special Satus */
static MOD_FunCbPtr currModFuncPtrs[MAX_FUNCTION_MOD];
//Main Menu Picture Ids
//static const UINT16 inactive_id[MAIN_ITEMCOUNT] = {GUI_IMG_MUSIC, GUI_IMG_RECORD, GUI_IMG_BT, GUI_IMG_FM, GUI_IMG_SYSTEM};
//static const UINT16 active_id[MAIN_ITEMCOUNT] = {GUI_IMG_MUSICA, GUI_IMG_RECORDA, GUI_IMG_BTA, GUI_IMG_FMA, GUI_IMG_SYSTEMA};
//static const UINT16 item_str_id[MAIN_ITEMCOUNT] = {GUI_STR_MUSIC, GUI_STR_RECORD, GUI_STR_BT, GUI_STR_FM, GUI_STR_SETTING};
//應用模塊ID
//static const UINT16 ap_id[MAIN_ITEMCOUNT]={RESULT_MUSIC, RESULT_RECORD_NOSTART,RESULT_BT, RESULT_RADIO, RESULT_SYSTEM};
/*********************************************************************************
* Description : 注冊功能模塊函數，提供外部調用
*
* Arguments :
*
* Returns :
*
* Notes :
*
*********************************************************************************/
INT32 APP_RegisterFunPtr(UINT8 mod, MOD_FunCbPtr cb)
{
if(cb == NULL || mod > MAX_FUNCTION_MOD)
{
return -1;
}
else
{
currModFuncPtrs[mod] = cb;
}
return 1;
}
/*********************************************************************************
* Description : 初始化注冊函數
*
* Arguments :
*
* Returns :
*
* Notes :
*
*********************************************************************************/
INT32 APP_InitialFunPtr(void)
{
INT32 i;
for(i = 0; i <= MAX_FUNCTION_MOD; i++)
{
currModFuncPtrs[i] = NULL;
}
//注冊各個模塊的入口函數
#if APP_SUPPORT_LCD==1
APP_RegisterFunPtr(FUN_CALENDAR, CALENDAR_Entry);
APP_RegisterFunPtr(FUN_SYSTEM_SETTING, SET_Entry);
APP_RegisterFunPtr(FUN_TIMER, TIMER_Entry);
#endif
#if APP_SUPPORT_RECORD==1
APP_RegisterFunPtr(FUN_RECORD, RECORD_Entry);
#endif
#if APP_SUPPORT_FM==1
APP_RegisterFunPtr(FUN_FM, FM_Entry);
#endif
#if APP_SUPPORT_LINEIN==1
APP_RegisterFunPtr(FUN_LINEIN, LINEIN_Entry);
#endif
APP_RegisterFunPtr(FUN_IDLE, IDLE_Entry);
#if APP_SUPPORT_MUSIC==1
APP_RegisterFunPtr(FUN_MUSIC, MUSIC_Entry);
#endif
#if APP_SUPPORT_USBDEVICE==1
APP_RegisterFunPtr(FUN_USB, USB_Entry);
#endif
#if APP_SUPPORT_BLUETOOTH==1
APP_RegisterFunPtr(FUN_BT, BT_Entry);
#endif
APP_RegisterFunPtr(FUN_CHARGING, Charging_Entry);
return 1;
}
/*********************************************************************************
* Description : 注冊功能模塊函數，提供外部調用
*
* Arguments :
*
* Returns :
*
* Notes :
*
*********************************************************************************/
INT32 APP_ModCall(UINT8 mod, INT32 Param)
{
hal_HstSendEvent(SYS_EVENT, 0x10140000 + mod);
g_current_module = mod;
if((mod < MAX_FUNCTION_MOD) && (currModFuncPtrs[mod] != NULL))
{
return currModFuncPtrs[mod](Param);
}
return -1;
}
/*********************************************************************************
* Description : 顯示系統開機動畫
*
* Arguments : wait_key_up, 是否要等待按鍵
*
* Returns : TRUE, 正常
FALSE, enter testmode
*
* Notes :
*
*********************************************************************************/
BOOL APP_DisplaySysLogo(BOOL wait_key_up)
{
INT32 i, j;
BOOL keydown = FALSE;
UINT32 key;
UINT32 prekey = 0;
hal_HstSendEvent(SYS_EVENT, 0x19884501);
hal_HstSendEvent(SYS_EVENT, g_displayconfig.log_image_time);
hal_HstSendEvent(SYS_EVENT, g_displayconfig.log_image_count);
if(g_displayconfig.log_image_count == 0 && g_displayconfig.log_image_time == 0)
{
for(i = 0; i < 1; i++)
for(j = 0; j < 1;)
{
key = MESSAGE_Wait();
//app_trace(APP_MAIN_TRC, "Display Log receive event 0x%x,prekey=0x%x, keydown=%d", key, prekey, keydown);
switch(key)
{
case AP_MSG_RTC:
case AP_MSG_CHARGING:
j++;
break;
default:
if((key & 0xffff) == AP_KEY_DOWN)
{
if(prekey != 0 || key != (AP_KEY_DOWN | AP_KEY_POWER))
{
keydown = TRUE;
}
prekey = key;
}
if(keydown && (key & 0xffff) == AP_KEY_UP)
{
return TRUE;
}
key = MESSAGE_HandleHotkey(key);//handle unusual usb/t-card/line-in pluging event
if(key != 0)
{
event_detected_displaying_log = key;
hal_HstSendEvent(SYS_EVENT, 0x13063002);
hal_HstSendEvent(SYS_EVENT, key);
}
break;
}
}
}
for(i = 0; i < g_displayconfig.log_image_count; i++)
{
#if APP_SUPPORT_RGBLCD==1
if(AP_Support_LCD())
{
GUI_ClearScreen(NULL);//清全屏幕
GUI_ResShowImage(GUI_IMG_LOGO, i, 0, 40); //g_displayconfig.log_x, g_displayconfig.log_y);/*BootLogo*/
GUI_UpdateScreen(NULL);
}
#elif APP_SUPPORT_LCD==1
if(AP_Support_LCD())
{
GUI_ClearScreen(NULL);//清全屏幕
GUI_ResShowImage(GUI_IMG_LOGO, i, 0, 8); //g_displayconfig.log_x, g_displayconfig.log_y);/*BootLogo*/
GUI_UpdateScreen(NULL);
}
#elif APP_SUPPORT_LED8S==1
GUI_ClearScreen(NULL);
GUI_ResShowPic(0xffff, 0, 0);
GUI_DisplayText(0, 0, "8888");
GUI_UpdateScreen(NULL);
#endif
hal_HstSendEvent(SYS_EVENT, 0x19884500);
hal_HstSendEvent(SYS_EVENT, g_displayconfig.log_image_time);
for(j = 0; j < g_displayconfig.log_image_time; )
{
key = MESSAGE_Wait();
//app_trace(APP_MAIN_TRC, "Display Log receive event 0x%x,prekey=0x%x, keydown=%d", key, prekey, keydown);
switch(key)
{
case AP_MSG_RTC:
case AP_MSG_CHARGING:
j++;
break;
default:
if((key & 0xffff) == AP_KEY_DOWN)
{
if(prekey != 0 || key != (AP_KEY_DOWN | AP_KEY_POWER))
{
keydown = TRUE;
}
prekey = key;
}
if(keydown && (key & 0xffff) == AP_KEY_UP)
{
return TRUE;
}
break;
}
}
}
return TRUE;
}
/*********************************************************************************
* Description : 初始化系統設置變量
*
* Arguments :
*
* Returns :
*
* Notes :
*
*********************************************************************************/
void APP_ReadComPara(void)
{
//DSM_ReadUserData();
//NVRAMRead(g_comval, VM_SYSTEM, sizeof(g_comval));
g_comval = (comval_t*)NVRAMGetData(VM_SYSTEM, sizeof(comval_t));
hal_HstSendEvent(SYS_EVENT, 0x19880900);
if(g_comval->magic != MAGIC_COMVAL)
{
hal_HstSendEvent(SYS_EVENT, 0x19880901);
if(!LoadFactorySetting(g_comval, sizeof(g_comval)))
{
g_comval->DisplayContrast = 5;
g_comval->langid = GUI_LANG_SM_CHINESE;
g_comval->LightTime = 3;
//g_comval->ReplayMode = 0;
//g_comval->SleepTime = 0;
g_comval->StandbyTime = 30;
//g_comval->BatteryType = BATT_TYPE_ALKALINE;
//g_comval->FMBuildInFlag = 0;
//g_comval->RecordType = 0;
//g_comval->BLightColor = 3;
g_comval->BackLight = 5;
g_comval->Volume = 8; // default volume
g_comval->music_cfg.loop_mode = 0;
g_comval->music_cfg.eq_mode = 0;
g_comval->music_cfg.repeat_count = 3;
g_comval->music_cfg.repeat_time = 30;
#if APP_SUPPORT_FM==1 /*Surport fm*/
g_comval->fm_value.fm_band = 0;
g_comval->fm_value.fm_sendfreq = 1000;
#endif
}
hal_HstSendEvent(SYS_EVENT, 0x19880902);
g_comval->magic = MAGIC_COMVAL;
// no need save data
//NVRAMWrite(g_comval, VM_SYSTEM,sizeof(g_comval));
//g_test_mode = 1;
}
if(!ReadConfigData(&g_sysconfig, CFG_SYSTEM, sizeof(g_sysconfig)))
{
g_sysconfig.AppSupportFlag = AP_SUPPORT_RECORD | (AP_SUPPORT_FM * APP_SUPPORT_FM) | (AP_SUPPORT_FMREC * APP_SUPPORT_FM_RECORD) | (AP_SUPPORT_LCD * APP_SUPPORT_LCD) | (AP_SUPPORT_MENU * APP_SUPPORT_MENU) | (AP_SUPPORT_LED * APP_SUPPORT_LED);
}
#if APP_SUPPORT_RGBLCD==1
if(AP_Support_LCD() && !ReadConfigData(&g_displayconfig, CFG_DISPLAY, sizeof(g_displayconfig)))
{
g_displayconfig.lcd_heigth = 128;
g_displayconfig.lcd_width = 160;
//g_displayconfig.log_x = 0;
//g_displayconfig.log_y = 8;
//g_displayconfig.usb_x = 0;
//g_displayconfig.usb_y = 16;
g_displayconfig.big_num_width = 16;
g_displayconfig.big_colon_width = 9;
g_displayconfig.small_num_width = 6;
g_displayconfig.small_colon_width = 4;
//g_displayconfig.num_key_img = GUI_IMG_BIG_NUM;
//g_displayconfig.num_key_x = 32;
//g_displayconfig.num_key_y = 16;
g_displayconfig.position_batt = POSITION_BATT;
g_displayconfig.message_y = 48;
}
#elif APP_SUPPORT_LCD==1
if(AP_Support_LCD() && !ReadConfigData(&g_displayconfig, CFG_DISPLAY, sizeof(g_displayconfig)))
{
g_displayconfig.lcd_heigth = 64;
g_displayconfig.lcd_width = 128;
//g_displayconfig.log_x = 0;
//g_displayconfig.log_y = 8;
//g_displayconfig.usb_x = 0;
//g_displayconfig.usb_y = 16;
g_displayconfig.big_num_width = 16;
g_displayconfig.big_colon_width = 9;
g_displayconfig.small_num_width = 6;
g_displayconfig.small_colon_width = 4;
//g_displayconfig.num_key_img = GUI_IMG_BIG_NUM;
//g_displayconfig.num_key_x = 32;
//g_displayconfig.num_key_y = 16;
g_displayconfig.position_batt = POSITION_BATT;
g_displayconfig.message_y = 24;
}
#endif
#if APP_SUPPORT_BLUETOOTH==1 /*Surport bt*/
if(!ReadConfigData(&g_btconfig, CFG_BLUETOOTH, sizeof(g_btconfig)))
{
strcpy(g_btconfig.local_name, "RDA MP3 BT"); // bluetooth name
strcpy(g_btconfig.password, "0000"); // bluetooth password
}
#endif
//SetBackLightColor(g_comval->BLightColor); //設置背光顏色。
SetBackLight(g_comval->BackLight);
SetContrast(g_comval->DisplayContrast); //設置屏幕的對比度
MESSAGE_Initial(g_comval);
}
INT32 APP_StandBy(void)
{
UINT32 key;
INT wakeup = 0;
GUI_DisplayMessage(0, GUI_STR_STANDBY, NULL, GUI_MSG_FLAG_WAIT);
if(AP_Support_LCD())
{
GUI_ClearScreen(NULL);//清全屏幕
GUI_UpdateScreen(NULL);
CloseBacklight();
}
ui_auto_update = FALSE;
//APP_Sleep();
#ifdef XDL_35uA_POWEROFF//warkey 2.1 //進入超低電流關機
rfd_XcvRegForceWrite32k();
#endif
while(1)
{
key = MESSAGE_Wait();
if(key == AP_MSG_RTC && GetBattery() >= 0)
{
if(tgt_GetKeyCode(0) == KEY_POWER)
{
app_trace(APP_MAIN_TRC, "APP_StandBy call DM_DeviceSwithOff");
DM_DeviceSwithOff();
}
else // 如果power鍵長高，無法關機，進入睡眠
{
app_trace(APP_MAIN_TRC, "APP_StandBy call APP_Sleep");
APP_Sleep();
}
continue;
}
if(key == (AP_KEY_POWER | AP_KEY_PRESS))
{
wakeup = 1;
}
if(key == (AP_KEY_PLAY | AP_KEY_HOLD))
if(MESSAGE_IsHold())
{
wakeup = 1;
}
if((key & 0xffff) == AP_KEY_UP && wakeup)
{
key = RESULT_POWERON;
break;
}
if(key == AP_MSG_ALARM)
{
key = RESULT_ALARM;
break;
}
}
APP_Wakeup();
return key;
}
#if APP_SUPPORT_CALIB_KEY==1
INT32 APP_CalibKey(void)
{
UINT32 key;
#ifdef _USED_TSC_KEY_
GUI_DisplayMessage(0, GUI_STR_CALIBKEY, NULL, GUI_MSG_FLAG_DISPLAY);
while(1)
{
tsd_Key_Calib(0); // start
key = MESSAGE_Wait();
if((key & 0xffff) == AP_KEY_UP)
{
break;
}
}
LED_SetPattern(GUI_LED_CALIB_KEY1, LED_LOOP_INFINITE);
GUI_DisplayMessage(0, GUI_STR_CALIBKEY_1, NULL, GUI_MSG_FLAG_DISPLAY);
while(1)
{
key = MESSAGE_Wait();
if((key & 0xffff) == AP_KEY_UP)
{
break;
}
}
tsd_Key_Calib(1); // first key press
LED_SetPattern(GUI_LED_CALIB_KEYN, LED_LOOP_INFINITE);
GUI_DisplayMessage(0, GUI_STR_CALIBKEY_N, NULL, GUI_MSG_FLAG_DISPLAY);
while(1)
{
key = MESSAGE_Wait();
if((key & 0xffff) == AP_KEY_UP)
{
break;
}
}
key = tsd_Key_Calib(2); // last key press
if(key == 0)
{
LED_SetPattern(GUI_LED_NONE, 0);
GUI_DisplayMessage(0, GUI_STR_CALIBKEY_SUCC, NULL, GUI_MSG_FLAG_WAIT);
}
else
{
GUI_DisplayMessage(0, GUI_STR_CALIBKEY_FAIL, NULL, GUI_MSG_FLAG_WAIT);
}
#endif
return 0;
}
#endif
BOOL APP_Read_Sys_Config(void)
{
#if 0
//////////////////////Set Para Through File//////////////////////////
INT32 config_file_handle = 0;
UINT8 buf[READ_BUF_MAX];
if(MountDisk(FS_DEV_TYPE_TFLASH))
{
config_file_handle = FS_Open(L"Config.txt", FS_O_RDONLY, 0);
}
#if APP_SUPPORT_USB
else if(MountDisk(FS_DEV_TYPE_USBDISK))
{
config_file_handle = FS_Open("Config.txt", FS_O_RDONLY, 0);
}
#endif
else
{
return FALSE;
}
if(config_file_handle < 0)
{
return FALSE;
}
///////Scan Param For Setting/////
memset(buf, 0, sizeof(buf));
buf[READ_BUF_MAX - 1] = '\n';
if(FS_Read(config_file_handle, buf, (sizeof(buf) - 1)))
{
//kval_t kval;
UINT16 uYear, uMonth, uDay, uHour, uMinute, uSecond, position;
/*First1:parse DATA*/
{
INT8 *str = "DATE:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
uYear = (buf[position] - '0') * 1000 + (buf[position + 1] - '0') * 100 + (buf[position + 2] - '0') * 10 + (buf[position + 3] - '0'); /*buf[0-3],Year... etc 2011 */
uMonth = (buf[position + 4] - '0') * 10 + (buf[position + 5] - '0'); /*buf[4-5],Month... etc 11 */
uDay = (buf[position + 6] - '0') * 10 + (buf[position + 7] - '0'); /*buf[6-7],Day... etc 11 */
str = "TIME:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
uHour = (buf[position] - '0') * 10 + (buf[position + 1] - '0'); /*buf[8-9],uHour... etc 11 */
uMinute = (buf[position + 2] - '0') * 10 + (buf[position + 3] - '0'); /*buf[10-11],uMinute... etc 11 */
uSecond = (buf[position + 4] - '0') * 10 + (buf[position + 5] - '0'); /*buf[12-13],uSecond... etc 21 */
}
app_trace(APP_MAIN_TRC, "[APP_Read_Sys_Config]:%d,%d,%d,%d,%d,%d\r\n", uYear, uMonth, uDay, uHour, uMinute, uSecond);
/*Get Band,FMFREQ*/
#if APP_SUPPORT_FM==1 /*Surport fm*/
{
INT8 *str = "BAND:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
g_comval->fm_value.fm_band = (buf[position] - '0');
str = "FMSEND:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
g_comval->fm_value.fm_sendfreq = (buf[position] - '0') * 1000 + (buf[position + 1] - '0') * 100 + (buf[position + 2] - '0') * 10 + (buf[position + 3] - '0');
}
#endif
/*Get Loop,Eq*/
{
INT8 *str = "LOOP:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
g_comval->music_cfg.loop_mode = (buf[position] - '0');
str = "EQ:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
g_comval->music_cfg.eq_mode = (buf[position] - '0');
}
/*Get repeat ,times*/
{
INT8 *str = "REPEAT:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
g_comval->music_cfg.repeat_count = (buf[position] - '0');
str = "REPETIME:" ;
position = strstr(buf, str) - buf;
position += strlen(str);
g_comval->music_cfg.repeat_time = (buf[position] - '0') * 10 + (buf[position + 1] - '0');
}
//將systemtime 和 gwtime寫回到VRAM中
//NVRAMRead(&kval, VM_KERNEL, sizeof(kval_t));
//kval.systemtime = ((uYear-2000)*365+uMonth*30+uDay)*24*60+uHour*60+uMinute; //全局變量
//NVRAMWrite(&kval, VM_KERNEL, sizeof(kval_t));
}
FS_Close(config_file_handle);
#endif
return TRUE;
}
INT32 main_menu_callback(INT32 type, INT32 value, INT32 param, UINT8 **string)
{
if(MENU_CALLBACK_QUERY_ACTIVE == type)
{
return g_last_reslt;
}
return FALSE;
}
TASK_ENTRY BAL_MainTaskEntry(void *pData)
{
INT8 IsUDisk = 0;
BOOL need_draw = TRUE;
INT32 active = 0; //當前活動的項目
INT32 result = APP_DEFAULT_RESULT;
INT32 ret = RESULT_NULL;
INT32 bt_active_ret = RESULT_NULL;
TM_SYSTEMTIME systime;
extern BOOL g_usb_connected;
// dump version and date
//hal_HstSendEvent(SYS_EVENT,0x11223344);
//hal_HstSendEvent(SYS_EVENT,GetPlatformVersion());
//hal_HstSendEvent(SYS_EVENT,GetPlatformRevision());
//hal_HstSendEvent(SYS_EVENT,GetPlatformBuildDate());
//hal_HstSendEvent(SYS_EVENT,AP_GetVersion());
//hal_HstSendEvent(SYS_EVENT,AP_GetBuildDate());
APP_ReadComPara(); //讀取系統的全局變量。可以放在os初始化的過程中做
#if XDL_APP_SUPPORT_LOWBAT_DETECT==1//warkey 2.1
StartBatTimer();
#endif
gui_load_resource(g_comval->langid);
LED_SetPattern(GUI_LED_POWERON, 1);
#if APP_SUPPORT_LCD==1
if(AP_Support_LCD())
{
lcdd_Open();
GUI_Initialise(g_displayconfig.lcd_width, g_displayconfig.lcd_heigth);
GUI_SetTextColor(g_displayconfig.font_color);
GUI_SetBackColor(g_displayconfig.back_color);
}
#endif
if(g_test_mode)
{
NVRAMWriteData();
APP_Test_Mode();
}
APP_DisplaySysLogo(FALSE);
AP_GetBuildDate();//force link date time functions.
// check systemtime
TM_GetSystemTime(&systime);
if(systime.uHour >= 24 || systime.uDay == 0 || systime.uYear > 2050) // invalid date time
{
systime.uYear = 2012;
systime.uMonth = 8;
systime.uDay = 15;
systime.uHour = 12;
systime.uMinute = 30;
TM_SetSystemTime(&systime);
}
#if APP_SUPPORT_LCD==1
TIMER_SetAlarm(1);
#endif
hal_HstSendEvent(SYS_EVENT, 0x09250001);
APP_InitialFunPtr(); //初始化各個模塊的回調函數，最后通過宏定義來實現開關
APP_Read_Sys_Config();
LED_SetPattern(GUI_LED_NONE, 1);
hal_HstSendEvent(BOOT_EVENT, 0x09558000);
#if APP_SUPPORT_LCD==0 //added for T_card update without LCD. Search TF card, if there is a file with the name "tflash_update.bin", then do the update.
#ifdef MCD_TFCARD_SUPPORT
{
INT32 file = -1, card_ok = -1;
UINT32 cur_data = AP_GetBuildDate();
UINT32 cur_time = AP_GetBuildTime();
boolean needupdate = FALSE;
hal_HstSendEvent(BOOT_EVENT, 0x98880001);
hal_HstSendEvent(BOOT_EVENT, cur_data);
hal_HstSendEvent(BOOT_EVENT, cur_time);
hal_HstSendEvent(BOOT_EVENT, 0x98880001);
card_ok = FS_MountDevice(FS_DEV_TYPE_TFLASH);
hal_HstSendEvent(BOOT_EVENT, card_ok);
if(card_ok == ERR_SUCCESS)
{
FS_FILE_ATTR file_attr;
TM_FILETIME sFileTime;
TM_SYSTEMTIME sSysTm;
UINT32 bin_createDate = 0;
UINT32 bin_createTime = 0;
UINT32 offset = 0;
file = FS_Open(UPDATE_TFLASH_BIN_NAME, FS_O_RDWR, 0);
hal_HstSendEvent(BOOT_EVENT, 0x09550000);
hal_HstSendEvent(BOOT_EVENT, file);
hal_HstSendEvent(BOOT_EVENT, 0x09550000);
#if 1
FS_Seek(file, 0xc, FS_SEEK_SET);
FS_Read(file, &offset, 4);
FS_Seek(file, ((offset & 0x00ffffff)) - 0x10, FS_SEEK_SET);
FS_Read(file, &bin_createDate, 4);
FS_Read(file, &bin_createTime, 4);
hal_HstSendEvent(BOOT_EVENT, 0x98880002);
hal_HstSendEvent(BOOT_EVENT, bin_createDate);
hal_HstSendEvent(BOOT_EVENT, bin_createTime);
hal_HstSendEvent(BOOT_EVENT, 0x98880002);
#else
if(FS_GetFileAttrByHandle(file, &file_attr) == 0)
{
sFileTime.DateTime = file_attr.i_mtime;
TM_FileTimeToSystemTime(sFileTime, &sSysTm);
bin_createDate = ((sSysTm.uYear) * 10000 + ((sSysTm.uMonth) * 100) + sSysTm.uDay);
bin_createTime = sSysTm.uHour * 10000 + sSysTm.uMinute * 100 + sSysTm.uSecond;
hal_HstSendEvent(BOOT_EVENT, 0x98880002);
hal_HstSendEvent(BOOT_EVENT, bin_createDate);
hal_HstSendEvent(BOOT_EVENT, bin_createTime);
hal_HstSendEvent(BOOT_EVENT, 0x98880002);
}
#endif
//if((cur_data<bin_createDate) ||
//(cur_data==bin_createDate && cur_time<bin_createTime))
if((cur_data != bin_createDate) || (cur_time != bin_createTime)) //只要不是同一軟件就允許升級
{
needupdate = TRUE;
}
hal_HstSendEvent(BOOT_EVENT, needupdate);
hal_HstSendEvent(BOOT_EVENT, 0x98880008);
if(file >= 0 && needupdate)
{
Upgrade_Flash(file);
RestartSystem();
}
else
{
FS_Close(file);
}
}
}
#endif
#endif
g_last_reslt = result;
if(GetUsbCableStatus())
{
hal_HstSendEvent(APP_EVENT, 0x13113001);
result = RESULT_UDISK;
}
if(gpio_detect_linein() == GPIO_DETECTED)
{
hal_HstSendEvent(APP_EVENT, 0x13113002);
result = RESULT_LINE_IN;
}
// IsUDisk = g_comval->Onlinedev;
#ifdef SUPPORT_POWERON_ENTER_CHARGE_AP//warkey 2.1
app_trace(APP_MAIN_TRC, "GetBattery:%d", GetBattery());
if(-1 == GetBattery() && g_usb_connected == 0)
{
// hal_HstSendEvent(SYS_EVENT, 0x13062707);
hal_HstSendEvent(APP_EVENT, 0x13113003);
result = Charging_Entry();
}
#endif
while(1)
{
if(result==RESULT_STANDBY)
{
LED_SetPattern(GUI_LED_NONE, 0xde);
}
else
{
LED_SetPattern(GUI_LED_NONE, 1);
}
hal_HstSendEvent(SYS_EVENT, 0x09250002);
hal_HstSendEvent(SYS_EVENT, result);
if(result == RESULT_NULL || result == RESULT_MAIN)
{
#if APP_SUPPORT_MENU==1
if(AP_Support_MENU())
{
ui_auto_select = FALSE;
result = GUI_Display_Menu(GUI_MENU_MAIN, main_menu_callback);
g_last_reslt = RESULT_NULL;
if(result == RESULT_TIMEOUT || result == RESULT_IGNORE || result == RESULT_NULL)
{
result = RESULT_IDLE; // RESULT_CALENDAR;
}
}
else
#endif
{
if(RESULT_STANDBY != result)
{
result = g_last_reslt;
}
switch(result)
{
case RESULT_STANDBY:
break;
case RESULT_BT:
#if APP_SUPPORT_MUSIC==1
result = RESULT_MUSIC;
break;
case RESULT_MUSIC:
#endif
#if APP_SUPPORT_FM || APP_SUPPORT_LINEIN
//沒有Line in時才進入FM 2012-9-27
if(gpio_detect_linein() == GPIO_DETECTED)
{
#if APP_SUPPORT_LINEIN ==1
result = RESULT_LINE_IN;
break;
#else
result = RESULT_RADIO;
break;
#endif
}
else
{
#if APP_SUPPORT_FM==1
result = RESULT_RADIO;
break;
#endif
}
case RESULT_LINE_IN:
case RESULT_RADIO:
#endif
#if APP_SUPPORT_RECORD
if(AP_Support_RECORD())
{
result = RESULT_RECORD_NOSTART;
break;
}
case RESULT_RECORD_NOSTART:
#endif
#if APP_SUPPORT_BLUETOOTH
result = RESULT_BT;
break;
#endif
default:
result = APP_DEFAULT_RESULT;
break;
}
}
}
else if(result == RESULT_POWERON)
{
if(AP_Support_LCD())
{
GUI_ClearScreen(NULL);
GUI_UpdateScreen(NULL);
}
LED_SetPattern(GUI_LED_POWERON, 1);
APP_DisplaySysLogo(TRUE);
LED_SetPattern(GUI_LED_NONE, 1);
if (g_comval->LightTime == 0) //每次開機判斷一次！解決Bug Report:27
{
CloseBacklight();
}
else
{
OpenBacklight();
}
//APP_DUMP("g_last_reslt:", g_last_reslt);
result = g_last_reslt;
if(GetUsbCableStatus())
{
hal_HstSendEvent(APP_EVENT, 0x07021549);
result = RESULT_UDISK;
}
if(gpio_detect_linein() == GPIO_DETECTED)
{
hal_HstSendEvent(APP_EVENT, 0x07021550);
result = RESULT_LINE_IN;
}
need_draw = TRUE;
}
else //boot with param or result != 0
{
switch( result)
{
#if APP_SUPPORT_MUSIC==1
case RESULT_MUSIC:
hal_HstSendEvent(SYS_EVENT, 0x20120000);
ret = APP_ModCall(FUN_MUSIC, 0);
g_last_reslt = result;
result = ret;
#if APP_SUPPORT_FADE_INOUT==1
if(g_fade_volume_backup != -1)
{
// hal_HstSendEvent(SYS_EVENT, 0x13101701);
// hal_HstSendEvent(SYS_EVENT, g_fade_volume_backup);
SetPAVolume(g_fade_volume_backup);
g_fade_volume_backup = -1;
}
#endif
if(g_usb_audio_tcard&&GetUsbCableStatus())//plug in tcard when usb audio is running
{
result = RESULT_UDISK;
}
hal_HstSendEvent(SYS_EVENT, 0x20124444);
hal_HstSendEvent(SYS_EVENT, g_last_reslt);
hal_HstSendEvent(SYS_EVENT, result);
break;
#endif
case RESULT_RADIO:
hal_HstSendEvent(SYS_EVENT, 0x20120033);
ret = APP_ModCall(FUN_FM, 0);
hal_HstSendEvent(SYS_EVENT, 0x20120044);
g_last_reslt = result;
result = ret;
hal_HstSendEvent(SYS_EVENT, 0x20123001);
break;
case RESULT_RECORD_START: //進入錄音
case RESULT_RECORD_NOSTART:
case RESULT_FMREC_START:
case RESULT_FMREC_NOSTART:
ret = APP_ModCall(FUN_RECORD, result); //傳入result,以判斷是否直接開始FM錄音?
…………
…………
…………限于本文篇幅余下代碼請從51黑下載附件…………

復制代碼

全部資料51hei下載地址：
開發手冊：

RDA5856開發文檔.zip (3.25 MB, 下載次數: 330)

源碼：

RDA585X-master.zip (12.26 MB, 下載次數: 118)

ID:402999 · 發表于 2018-9-27 09:37

支持一下看看

ID:419143 · 發表于 2018-11-1 15:16

打個點，等黑幣夠了再來下

ID:136083 · 發表于 2018-11-23 15:32

大佬，你自己看過沒有，這代碼不是5856的哈。

ID:185161 · 發表于 2019-4-13 23:42

這個芯片資料好少啊。廠家官網都打不開。。

ID:589216 · 發表于 2019-7-23 20:14

資料好少啊

ID:196917 · 發表于 2019-8-16 13:16

沒有包含硬件資料

ID:601446 · 發表于 2019-9-10 17:32

正好需要這個資料啊，謝謝樓主

ID:219315 · 發表于 2019-9-19 21:03

謝謝樓主!!!!!

ID:619051 · 發表于 2019-10-3 19:05

謝謝樓主正需要呢

ID:160131 · 發表于 2019-12-6 09:35

你好，可以請教你一個問題嗎

ID:476744 · 發表于 2019-12-15 09:00

不錯，很好的資料

ID:232306 · 發表于 2020-10-5 10:45

已經下載，多謝樓主

ID:232306 · 發表于 2020-10-5 10:50

開發環境怎么搭建？

ID:486587 · 發表于 2021-10-16 12:03

正好需要這個資料，如果有SDK就更好了

ID:1036193 · 發表于 2023-5-11 20:17

正好需要這個資料，如果有SDK就更好了

帳號		自動登錄	找回密碼
密碼			立即注冊

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

RDA5856代碼開發手冊 IOT藍牙雙模芯片源碼與資料下載

評分