微型逆變器設(shè)計資料及源碼

ID:367943 · 發(fā)表于 2018-7-9 14:54

內(nèi)容包括：
1. PCB 原理圖 GERBER文件
2. BOM清單
3. MATLAB仿真工程
4. 源代碼工程

The 230Vac Solar Microinverter Design Package contains the following:
- Application Note
- Schematic and Layout Files
- Gerber Files
- Source Code
- MATLAB Models
- Bill of Materials
- Demo Instructions

Getting Started:
See Grid Connected Solar Microinverter Demo Instructions.pdf for instructions on demonstration setup.

Known Issues:
The Solar Microinverter currently uses the passive method for detecting Grid failures. A future software update is planned to implement active method for anti-islanding.

電路原理圖如下：

全部資料51hei下載地址：

230Vac Grid-Connected Solar Microinverter Design Package.zip (2.45 MB, 下載次數(shù): 138)

部分源代碼如下

/////////////////////////////////////////////////////////////////////////////////////////////////
// ?2012 Microchip Technology Inc.
//
// MICROCHIP SOFTWARE NOTICE AND DISCLAIMER: You may use this software, and any
// derivatives created by any person or entity by or on your behalf, exclusively with
// Microchip抯 products. Microchip and its licensors retain all ownership and intellectual
// property rights in the accompanying software and in all derivatives here to.
//
// This software and any accompanying information is for suggestion only. It does not
// modify Microchip抯 standard warranty for its products. You agree that you are solely
// responsible for testing the software and determining its suitability. Microchip has
// no obligation to modify, test, certify, or support the software.
//
// THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF NON-INFRINGEMENT,
// MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE, ITS INTERACTION
// WITH MICROCHIP扴 PRODUCTS, COMBINATION WITH ANY OTHER PRODUCTS, OR USE IN ANY APPLICATION.
//
// IN NO EVENT, WILL MICROCHIP BE LIABLE, WHETHER IN CONTRACT, WARRANTY, TORT
// (INCLUDING NEGLIGENCE OR BREACH OF STATUTORY DUTY), STRICT LIABILITY, INDEMNITY,
// CONTRIBUTION, OR OTHERWISE, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, INCIDENTAL
// OR CONSEQUENTIAL LOSS, DAMAGE, FOR COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
// SOFTWARE, HOWSOEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR
// THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWABLE BY LAW, MICROCHIP'S TOTAL
// LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES,
// IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
//
// MICROCHIP PROVIDES THIS SOFTWARE CONDITIONALLY UPON YOUR ACCEPTANCE OF THESE TERMS.
//
/////////////////////////////////////////////////////////////////////////////////////////////////
#include "Solar Microinverter_Statemachine.h"
// System Fault Variables
unsigned char storeFaultState = 0, faultCheckFlag = 0, criticalFaultRestartFlag = 0;
unsigned char pvPanelOverVoltageFlag = 0, pvPanelUnderVoltageFlag = 0, overTemperatureFlag = 0;
unsigned char inverterOverVoltageFlag = 0, inverterUnderVoltageFlag = 0, pvUnderVoltageCounter = 0;
unsigned char inverterUnderVoltageCounter = 0, inverterOverVoltageCounter = 0;
unsigned char tempFaultCnt = 0, driveSupplyFaultCnt = 0, referenceVoltageFaultCnt = 0;
unsigned int criticalFaultCounter = 0, pvPanelMPPOverVoltageCnt = 0;
unsigned int inverterOutputOverCurrent = 0;
// Start-up and Restart Variables
unsigned char zeroCrossDelay = 45, startFullBridgeFlag = 0;
unsigned char zeroCrossDelayNom = 30, zeroCrossDelayMin = 22, zeroCrossDelayMax = 37;
unsigned char acCurrentOffsetFlag = 0, acCurrentOffsetCounter = 0;
unsigned int systemRestartCounter = 0, acCurrentOffset = 0;
unsigned int inverterPeriodMin = INVERTERPERIOD60HZMIN, inverterPeriodMax = INVERTERPERIOD50HZMAX;
long unsigned int acCurrentOffsetAverage = 0;
// MPPT and Load Balance Variables
unsigned char loadBalanceCounter = 0, mpptCounter = 0, mpptStartUpFlag = 0;
unsigned int inputVoltageAverage = 0, inputCurrentAverage = 0, openCircuitVoltage = 0;
unsigned int mpptFactor = MPPTFACTORMINIMUM;
int inputPower = 0, prevInputVoltageAverage = 0, deltaDutyCycle = 0;
// Startup in system error, If a fault is detected
// faultstate will change during the restart counter.
unsigned char systemState = SYSTEMERROR;
unsigned char switchState = SWITCHOFF;
unsigned char faultState = NO_FAULT;
// Externally Defined Variables
extern unsigned char avgInputDataReadyFlag, startupZeroCrossCounter;
extern unsigned char criticalFaultFlag, acCurrentOffsetFlag, ninetyDegreeDetectFlag;
extern unsigned char burstModeActiveFlag;
extern unsigned int mpptFactorMaximum, numberofSamples;
extern unsigned int measuredTemperature, driveSupplyVoltage, referenceVoltage;
extern unsigned int averageFlybackCurrent1, averageFlybackCurrent2;
extern unsigned int inverterPeriod, peakInverterOutputVoltage, burstModeActiveCounter;;
extern int inverterOutputCurrent;
// Variable Declaration for DMCI Debugging Tool
#ifdef DMCI_STATEMACHINE
int array1[100];
int array2[100];
int array3[100];
unsigned char dmciArrayIndex = 0;
#endif
#ifdef DMCI_MPPT
int array1[100];
int array2[100];
int array3[100];
unsigned char dmciArrayIndex = 0;
#endif
// Timer 3 Interrupt (300ms interrupt) for Fault indication
void __attribute__((__interrupt__, no_auto_psv)) _T3Interrupt()
{
static unsigned char ledCounter = 0, interruptCounter = 0;
if(ledCounter < storeFaultState)
{
LED_DRV1 ^= ON; // Blink LED to indicate fault, storeFaultState is 2x to account for toggle Off
ledCounter++;
}
else if (ledCounter < (storeFaultState + 3)) // Wait three interrupts (Clear indication blinking has stopped)
{
ledCounter++;
}
else
{
ledCounter = 0;
}
if(systemState == DAYMODE)
{
interruptCounter++;
}
// InterruptCounter is used to diplay the last known fault for some time after
// the system restarts (300ms * 200 ~ 1 minute)
if((faultState == NO_FAULT) && (interruptCounter >= 200))
{
T3CONbits.TON = 0; //Disable this interrupt if the fault is removed and the delay has passed
ledCounter = 0;
interruptCounter = 0;
LED_DRV1 = OFF;
}
TMR3 = 0;
IFS0bits.T3IF = 0;
}
// Timer 2 Interrupt (100us interrupt), performs fault checking and system statemachine
void __attribute__((__interrupt__, no_auto_psv)) _T2Interrupt()
{
// Check Inverter Output Over Voltage Condition
if((peakInverterOutputVoltage > INVERTER_OVERVOLTAGE_LIMIT) && (inverterOverVoltageFlag == 0))
{
inverterOverVoltageCounter++;
if(inverterOverVoltageCounter >= 2)
{
if(faultState == NO_FAULT)
{
faultState = INVERTER_VOLTAGE;
inverterOverVoltageFlag = 1;
}
}
}
else if((peakInverterOutputVoltage < INVERTER_OVERVOLTAGE_LIMIT_HYS) && (inverterOverVoltageFlag == 1))
{
if(faultState == INVERTER_VOLTAGE)
{
faultState = NO_FAULT;
}
inverterOverVoltageFlag = 0;
}
else
{
inverterOverVoltageCounter = 0;
}
if((peakInverterOutputVoltage < INVERTER_UNDERVOLTAGE_LIMIT) && (inverterUnderVoltageFlag == 0))
{
inverterUnderVoltageCounter++;
if(inverterUnderVoltageCounter >= 2)
{
if(faultState == NO_FAULT)
{
faultState = INVERTER_VOLTAGE;
inverterUnderVoltageFlag = 1;
}
inverterUnderVoltageCounter = 2;
}
}
else if ((peakInverterOutputVoltage > INVERTER_UNDERVOLTAGE_LIMIT_HYS) && (inverterUnderVoltageFlag == 1))
{
if(faultState == INVERTER_VOLTAGE)
{
faultState = NO_FAULT;
}
inverterUnderVoltageFlag = 0;
}
else
{
inverterUnderVoltageCounter = 0;
}
// Only Check Input Voltage Fault When New Data is Available
if(avgInputDataReadyFlag == 1)
{
// Check PV Panel Voltage Using the Average Input Voltage
if((inputVoltageAverage > PVPANEL_OVERVOLTAGE_LIMIT) && (pvPanelOverVoltageFlag == 0))
{
if(faultState == NO_FAULT)
{
faultState = PV_PANEL_VOLTAGE;
pvPanelOverVoltageFlag = 1;
}
}
else if((inputVoltageAverage < PVPANEL_OVERVOLTAGE_LIMIT_HYS) && (pvPanelOverVoltageFlag == 1))
{
if(faultState == PV_PANEL_VOLTAGE)
{
faultState = NO_FAULT;
}
pvPanelOverVoltageFlag = 0;
}
// Check PV Panel Maximum Power Point Voltage Using the Average Input Voltage
if((inputVoltageAverage > PVPANEL_MPP_LIMIT) && (systemState == DAYMODE))
{
pvPanelMPPOverVoltageCnt++;
// Allow time for system to find MPP
if(pvPanelMPPOverVoltageCnt > 1000)
{
pvPanelOverVoltageFlag = 1; // Set Flag so System Will Restart
pvPanelMPPOverVoltageCnt = 0;
if(faultState == NO_FAULT)
{
faultState = PV_PANEL_VOLTAGE;
}
}
}
else
{
pvPanelMPPOverVoltageCnt = 0;
}
// Check PV Panel Minimum Voltage Using Average Input Voltage
if((inputVoltageAverage < PVPANEL_UNDERVOLTAGE_LIMIT) && (pvPanelUnderVoltageFlag == 0))
{
pvUnderVoltageCounter++;
if(pvUnderVoltageCounter >= 10)
{
if(faultState == NO_FAULT)
{
faultState = PV_PANEL_VOLTAGE;
pvPanelUnderVoltageFlag = 1;
}
pvUnderVoltageCounter = 10;
}
}
else if ((inputVoltageAverage > PVPANEL_UNDERVOLTAGE_LIMIT_HYS) && (pvPanelUnderVoltageFlag == 1))
{
if(faultState == PV_PANEL_VOLTAGE)
{
faultState = NO_FAULT;
}
pvPanelUnderVoltageFlag = 0;
}
else
{
pvUnderVoltageCounter = 0;
}
}
// Check Over Temperature Fault
if((measuredTemperature >= MAXTEMPERATURE) && (overTemperatureFlag == 0))
{
tempFaultCnt++;
if(tempFaultCnt > 100)
{
tempFaultCnt = 100;
if(faultState == NO_FAULT)
{
faultState = TEMPERATURE;
overTemperatureFlag = 1;
}
}
}
else if ((measuredTemperature <= MAXTEMPERATURE_HYS) && (overTemperatureFlag == 1))
{
overTemperatureFlag = 0;
if(faultState == TEMPERATURE)
{
faultState = NO_FAULT;
}
}
else
{
tempFaultCnt = 0;
}
//Check 12V Drive Supply Voltage
if((driveSupplyVoltage > MAXDRIVEVOLTAGE) || (driveSupplyVoltage < MINDRIVEVOLTAGE))
{
driveSupplyFaultCnt++;
if(driveSupplyFaultCnt > 10)
{
driveSupplyFaultCnt = 10;
if(faultState == NO_FAULT)
{
faultState = DRIVE_SUPPLY;
}
}
}
else
{
driveSupplyFaultCnt = 0;
if(faultState == DRIVE_SUPPLY)
{
faultState = NO_FAULT;
}
}
// Check Reference Voltage
if((referenceVoltage < MINREFERENCEVOLTAGE) || (referenceVoltage > MAXREFERENCEVOLTAGE))
{
referenceVoltageFaultCnt++;
if(referenceVoltageFaultCnt > 10)
{
referenceVoltageFaultCnt = 10;
if(faultState == NO_FAULT)
{
faultState = REFERENCE_VOLTAGE;
}
}
}
else
{
referenceVoltageFaultCnt = 0;
if (faultState == REFERENCE_VOLTAGE)
{
faultState = NO_FAULT;
}
}
// Check the fault state, if it is not equal to No Fault then set systemState = SYSTEM_ERROR
if (faultState != NO_FAULT)
{
systemState = SYSTEMERROR;
}
// Check the On/Off switch state
if(PORTCbits.RC11 == 0)
{
switchState = SWITCHON;
}
else
{
//put system state in systemError
switchState = SWITCHOFF;
systemState = SYSTEMERROR;
}
switch(systemState)
{
case SYSTEMSTARTUP:
{
if(avgInputDataReadyFlag == 1)
{
// During system startup read the PV panel Voltage (open circuit voltage). This information
// is used to help speed up the time to find MPP
openCircuitVoltage = inputVoltageAverage;
avgInputDataReadyFlag = 0;
}
// Read AC Current offset during startup mode and verify data
// Needs to be completed before the full-bridge is enabled during system startup
if(acCurrentOffsetFlag == 0)
{
acCurrentOffsetAverage = acCurrentOffsetAverage + inverterOutputCurrent;
if(acCurrentOffsetCounter >= 255)
{
acCurrentOffset = (acCurrentOffsetAverage >> 8);
inverterOutputOverCurrent = INVERTER_OUTPUTCURRENT_MAX + (16383 - acCurrentOffset);
acCurrentOffsetFlag = 1;
acCurrentOffsetCounter = 0;
acCurrentOffsetAverage = 0;
if((acCurrentOffset < MINOFFSETCURRENT) || (acCurrentOffset > MAXOFFSETCURRENT))
{
if(faultState == NO_FAULT)
{
faultState = ACCURRENT_OFFSET;
}
}
}
else
{
acCurrentOffsetCounter++;
}
}
// At system Start-up, enable the Full-Bridge circuit (@ peak of AC Cycle) before the flyback circuit is enabled
// If this is not done, the flyback output will have high DC voltage and when the full-bridge is enabled at the
// zero cross there is a large dv/dt and the output current will have a large glitch and also trip the flyback
// OVP circuit
if((startupZeroCrossCounter >= (ZEROCROSSCOUNT>>1)) && (ninetyDegreeDetectFlag == 1))
{
startFullBridgeFlag = 1; // Set Flag to start full-bridge drive
}
// After several consecutive zero crossings switch to Day Mode
if(startupZeroCrossCounter > ZEROCROSSCOUNT)
{
if ((inverterPeriod > INVERTERPERIOD60HZMIN ) && (inverterPeriod <= INVERTERPERIOD60HZMAX))
{
inverterPeriodMin = INVERTERPERIOD60HZMIN;
inverterPeriodMax = INVERTERPERIOD60HZMAX;
// Delay at the zero crossings to allow AC voltage to reach flyback voltage
zeroCrossDelayNom = 20;
zeroCrossDelayMax = 22; // Delay slightly varies with AC voltage
zeroCrossDelayMin = 18;
zeroCrossDelay = zeroCrossDelayNom; // Wait (17us*delay) at the zero cross before turning on flyback/full-bridge
}
else
{
inverterPeriodMin = INVERTERPERIOD50HZMIN;
inverterPeriodMax = INVERTERPERIOD50HZMAX;
// Delay at the zero crossings to allow AC voltage to reach flyback voltage
zeroCrossDelayNom = 30;
zeroCrossDelayMax = 35; // Delay slightly varies with AC voltage
zeroCrossDelayMin = 25;
zeroCrossDelay = zeroCrossDelayNom; // Wait (17us*delay) at the zero cross before turning on flyback/full-bridge
}
// Change system state to Day Mode
systemState = DAYMODE;
}
}
break;
case DAYMODE:
{
// When average input voltage and average input current are available call MPPT Routine
if(avgInputDataReadyFlag == 1)
{
#ifndef BENCHTESTING
MPPTRoutine(); // Call MPPT Routine when data is ready
#endif
// Change Current Reference based on the PV panel voltage
if(inputVoltageAverage >= PVPANEL_40V)
{
CMPDAC2bits.CMREF = 700; // Consider current at ~39V
CMPDAC3bits.CMREF = 700;
}
else if(inputVoltageAverage >= PVPANEL_30V)
{
CMPDAC2bits.CMREF = 850; // Consider current at ~29V
CMPDAC3bits.CMREF = 850;
}
else
{
CMPDAC2bits.CMREF = 1000; // Consider current at ~20V
CMPDAC3bits.CMREF = 1000;
}
avgInputDataReadyFlag = 0;
}
// Load Balance routine to make sure that both flyback converters are sharing the load equally ~50%
// Execute at a slower rate 100us * LOADBALCOUNT
if(loadBalanceCounter >= LOADBALCOUNT)
{
LoadBalance(); // Call Load Balance Routine
loadBalanceCounter = 0;
}
loadBalanceCounter++;
// Software for soft-start when using a bench supply as MPP-Tracking is removed
#ifdef BENCHTESTING
mpptCounter++;
if(mpptFactor < MPPTFACTOR_BENCHTESTING)
{
if(mpptCounter >= MPPTCOUNT)
{
mpptFactor = mpptFactor + MPPTFACTORINCREMENT;
mpptCounter = 0;
}
}
else
{
mpptFactor = MPPTFACTOR_BENCHTESTING;
mpptCounter = 0;
}
#endif
}
break;
case SYSTEMERROR:
{
IOCON1bits.OVRENH = 1;
IOCON1bits.OVRENL = 1;
IOCON2bits.OVRENH = 1;
IOCON2bits.OVRENL = 1;
IOCON3bits.OVRENH = 1;
IOCON3bits.OVRENL = 1;
OPTO_DRV1 = 0;
OPTO_DRV2 = 0;
mpptStartUpFlag = 0;
startFullBridgeFlag = 0; // Reset flag to start full-bridge
burstModeActiveCounter = 0; // Reset burst mode
burstModeActiveFlag = 0;
acCurrentOffset = 0;
acCurrentOffsetFlag = 0; // Allow system to re-calculate AC Current Offset
mpptFactor = MPPTFACTORMINIMUM;
inputPower = 0;
prevInputVoltageAverage = 0;
ClrWdt(); // In fault mode we need to clear WDT
if((switchState == SWITCHON) && (faultState == NO_FAULT))
{
// Switch to system startup after no faults have been detected for ~1s
systemRestartCounter++;
if(systemRestartCounter >= RESTARTCOUNT)
{
systemState = SYSTEMSTARTUP;
systemRestartCounter = 0;
}
}
else if((switchState == SWITCHON) && (faultState != NO_FAULT))
{
// If a fault is present then diplay the fault using T3 and LED D27 on the PCB
systemRestartCounter = 0;
storeFaultState = (faultState << 1); // x2 to account for "off" time
T3CONbits.TON = 1;
// Remove the fault and allow system to try to restart
// If the fault is ac current offset or HW Zero Cross
if((faultState == ACCURRENT_OFFSET) || (faultState == HARDWAREZEROCROSS))
{
faultState = NO_FAULT;
}
// Critical Faults: AC Current, Flyback Over Voltage, and Flyback Over Current
// Handle faults differently: Allow system to try to restart only once, if fault
// is still present then disable PWM module.
if((criticalFaultFlag == 1) && (criticalFaultRestartFlag == 0))
{
criticalFaultCounter++;
// After 2s remove the critical fault and allow system to try to restart
if(criticalFaultCounter > CRITICALFAULTCOUNT)
{
criticalFaultRestartFlag = 1;
// As the fault for flyback over current is latched the PWM needs to
// exit the latched fault mode in order to restart
if(faultState == FLYBACK_OVERCURRENT)
{
FCLCON1bits.FLTMOD = 3; // Disable Fault Mode
FCLCON2bits.FLTMOD = 3; // Disable Fault Mode
FCLCON1bits.FLTMOD = 0; // Latched Fault Mode
FCLCON2bits.FLTMOD = 0; // Latched Fault Mode
}
faultState = NO_FAULT;
criticalFaultCounter = 0;
}
}
}
else if (switchState == SWITCHOFF)
{
// Reset Period Limits if switch is off
// This is only required for testing 50/60 Hz operation
// without having to cycle power
inverterPeriodMin = INVERTERPERIOD60HZMIN;
inverterPeriodMax = INVERTERPERIOD50HZMAX;
T3CONbits.TON = 0;
LED_DRV1 = OFF;
}
}
break;
}
// Software for debugging purposes
#ifdef DMCI_STATEMACHINE
array1 [dmciArrayIndex] = deltaDutyCycle;
array2 [dmciArrayIndex] = averageFlybackCurrent2 - averageFlybackCurrent1;
array3 [dmciArrayIndex++] = 0;
if(dmciArrayIndex >= 100)
{
dmciArrayIndex = 0;
}
#endif
TMR2 = 0;
IFS0bits.T2IF = 0;
}
// This MPPT algorithim implements the Perturbation and Observation method for detecting Maximum
// Power Point. MPPT can be up to ~25000
void MPPTRoutine(void)
{
int deltaV = 0, prevInputPower = 0;
unsigned char mpptScaleFactor = 0;
//Store off previous inputPower
prevInputPower = inputPower;
// Calculate new input power and change in input voltage
inputPower = (__builtin_mulss((int)inputVoltageAverage ,(int)inputCurrentAverage) >> 15);
deltaV = inputVoltageAverage - prevInputVoltageAverage;
// If there is a large drop in voltage decrease mpptFactor at a faster rate
// Example would be large AC voltage fluctuations
if(deltaV <= PVPANEL_VOLTAGEDROP)
{
mpptFactor = mpptFactor - (mpptFactor >> 2); // Reset to 75% power
}
// To find MPP faster, increase mpptFactor at a faster rate until the operating voltage
// is less than the opencircuit voltage minus ~3V. Vmp and Voc should always be more
// than 5-6V difference at any operating temperature or irradiance.
if((inputVoltageAverage > (openCircuitVoltage - 1650)) && (mpptStartUpFlag == 0))
{
mpptFactor += 50;
}
else
{
mpptStartUpFlag = 1;
criticalFaultFlag = 0; // If system gets here without a critical fault, allow system to run as normal
criticalFaultRestartFlag = 0;
}
if(burstModeActiveFlag == 1)
{
mpptScaleFactor = 1;
}
else
{
mpptScaleFactor = 0;
}
if (inputPower > prevInputPower)
{
if (deltaV < -LARGEVOLTAGEDIFFERENCE)
{
mpptFactor += MININCREMENTMPPTFACTOR;
}
else if (deltaV < 0)
{
mpptFactor += MAXINCREMENTMPPTFACTOR;
}
else if (deltaV > LARGEVOLTAGEDIFFERENCE)
{
mpptFactor -= (MAXDECREMENTMPPTFACTOR << mpptScaleFactor);
}
else if (deltaV > 0)
{
mpptFactor -= (MINDECREMENTMPPTFACTOR << mpptScaleFactor);
}
}
else if (inputPower < prevInputPower)
{
if (deltaV < -LARGEVOLTAGEDIFFERENCE)
{
mpptFactor -= (MAXDECREMENTMPPTFACTOR << mpptScaleFactor);
}
else if (deltaV < 0)
{
mpptFactor -= (MINDECREMENTMPPTFACTOR << mpptScaleFactor);
}
else if (deltaV > LARGEVOLTAGEDIFFERENCE)
{
mpptFactor += MAXINCREMENTMPPTFACTOR;
}
else if (deltaV > 0)
{
mpptFactor += MININCREMENTMPPTFACTOR;
}
}
// Saturate the MPPT limit to min and max values
if(mpptFactor > mpptFactorMaximum)
{
mpptFactor = mpptFactorMaximum;
}
else if(mpptFactor < MPPTFACTORMINIMUM)
{
mpptFactor = MPPTFACTORMINIMUM;
}
// Store off last known input power and input voltage
prevInputVoltageAverage = inputVoltageAverage;
// Software for debugging purposes
#ifdef DMCI_MPPT
array1 [dmciArrayIndex] = mpptFactor;
array2 [dmciArrayIndex] = deltaV;
array3 [dmciArrayIndex++] = inputPower;
if(dmciArrayIndex >= 100)
{
dmciArrayIndex = 0;
}
#endif
}
void LoadBalance(void)
{
static int loadBalIoutput = 0;
int diffFlybackCurrent = 0, loadBalPoutput = 0, loadBalPIoutput = 0;
// Difference of the two Flyback MOSFET Currents
diffFlybackCurrent = averageFlybackCurrent2 - averageFlybackCurrent1;
// Error * Proportional Gain
loadBalPoutput = ( (__builtin_mulss(diffFlybackCurrent,(int)KAQ15)) >> 15);
// Error * Integral Gain
loadBalIoutput = loadBalIoutput + ( (__builtin_mulss(diffFlybackCurrent,(int)KSAQ15)) >> 15);
// Check for Integral term exceeding MAXBALANCE, If true, saturate the integral term to MAXBALANCE
// Check for Integral term going below -MAXBALANCE, If true, saturate the integral term to -MAXBALANCE
if(loadBalIoutput > MAXBALANCE)
{
loadBalIoutput = MAXBALANCE;
}
else if(loadBalIoutput < -MAXBALANCE)
{
loadBalIoutput = -MAXBALANCE;
}
// PI Output = Proportional Term + Integral Term
loadBalPIoutput = loadBalPoutput + loadBalIoutput;
// Check for PI Output exceeding MAXBALANCE, If true, saturate PI Output to MAXBALANCE
// Check for PI Output going below -MAXBALANCE, If true, saturate PI Output to -MAXBALANCE
if(loadBalPIoutput > MAXBALANCE)
{
loadBalPIoutput = MAXBALANCE;
}
else if(loadBalPIoutput < -MAXBALANCE)
{
loadBalPIoutput = -MAXBALANCE;
}
// Delta duty cycle to correct the two Flyback MOSFET duty cycles
deltaDutyCycle = ( (__builtin_mulss((int)loadBalPIoutput,(int)FLYBACKPERIOD)) >> 15);
}