|
|
STM32F405的adc采集配置中感覺ADC的設置都對了為什么采集不到數據呢。下面是程序，有錯誤的地方幫忙指出來謝謝。
void ADC1_Init()
{
DMA_InitTypeDef DMA_InitStructure;
ADC_CommonInitTypeDef ADC_CommonInitStructure;
ADC_InitTypeDef ADC_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2 | RCC_AHB1Periph_GPIOC, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC1,ENABLE); //ADC1復位
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
GPIO_Init(GPIOC, &GPIO_InitStructure);
DMA_DeInit(DMA2_Stream0);
DMA_InitStructure.DMA_Channel= DMA_Channel_0;
DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)&ADC1->DR;
DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)&ADCConvertedValue; //(u32)&ADC_ConvertedValue接收到的數據存放在ADC_ConvertedValue里面
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory ; //外設設為數據源
DMA_InitStructure.DMA_BufferSize = N*M;
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;//數據寬度為16位
DMA_InitStructure.DMA_MemoryDataSize=DMA_MemoryDataSize_HalfWord; //數據寬度為16位
DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //工作在循環緩存模式
DMA_InitStructure.DMA_Priority = DMA_Priority_High;//DMA通道X擁有高優先級
DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable; //指定fifo模式還是直接模式
DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_HalfFull;//指定fifo閾值
DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single; //內存突發每次傳輸一個數據
DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;//外設突發每次傳輸一個數據
//DMA_InitStructure.DMA_M2M = DMA_M2M_Disable; //DMA通道X沒有設置為內存到內存?zhèn)鬏?br />
DMA_Init(DMA2_Stream0,&DMA_InitStructure); //根據DMA_InitStruct中指定的參數初始化DMA的通道
DMA_Cmd(DMA2_Stream0,ENABLE);
// NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
// NVIC_InitStructure.NVIC_IRQChannel =DMA2_Stream0_IRQn;
// NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
// NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
// NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
// NVIC_Init(&NVIC_InitStructure);
ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;//獨立模式，即軟件觸發模式
ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;//兩個采樣階段之間的延遲5個時鐘
ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled; //DMA失能
ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div4;//預分頻4分頻。ADCCLK=PCLK2/4=84/4=21Mhz,ADC時鐘最好不要超過36Mhz //配置ADC的時鐘分頻
ADC_CommonInit(&ADC_CommonInitStructure);//初始化
ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;//12位模式
ADC_InitStructure.ADC_ScanConvMode = ENABLE;//模數轉換工作在掃描模式
ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;//模數轉換工作在連續掃描模式
ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;//
// ADC_InitStructure.ADC_ExternalTrigConv =ADC_ExternalTrigConv_Ext_IT11;//
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;//右對齊
ADC_InitStructure.ADC_NbrOfConversion = 1;//通道數
ADC_Init(ADC1, &ADC_InitStructure);//ADC初始化
//ADC_ExternalTrigInjectedConvConfig(ADC1,ADC_ExternalTrigInjecConv_T2_TRGO);
ADC_RegularChannelConfig(ADC1,ADC_Channel_12,1,ADC_SampleTime_56Cycles);
////// ADC_MultiModeDMARequestAfterLastTransferCmd(ENABLE);DMA節點為多adc模式開啟或者關斷
ADC_DMARequestAfterLastTransferCmd(ADC1, ENABLE);
/* Enable ADC1 DMA */
ADC_DMACmd(ADC1, ENABLE);
/* Enable ADC1 */
DMA_ITConfig(DMA2_Stream0,DMA_IT_TC, ENABLE);//開啟DMA中斷
ADC_Cmd(ADC1, ENABLE);//開啟AD轉換器
ADC_SoftwareStartConv(ADC1);
// while(RESET == DMA_GetFlagStatus(DMA2_Stream0,DMA_FLAG_TCIF0));
}
|
|
